- 您现在的位置：买卖IC网 > PDF目录11819 > SC28L198A1BE,528 (NXP Semiconductors)IC UART OCTAL SOT407-1 PDF资料下载
参数资料
| 型号： | SC28L198A1BE,528 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 20/57页 |
| 文件大小： | 0K |
| 描述： | IC UART OCTAL SOT407-1 |
| 标准包装： | 1,000 |
| 特点： | 故障启动位检测 |
| 通道数： | 8 |
| FIFO's： | 16 字节 |
| 电源电压： | 3.3V，5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（14x14） |
| 包装： | 带卷 (TR) |
| 其它名称： | 935262731528 SC28L198A1BE-T SC28L198A1BE-T-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
Philips Semiconductors
Product data sheet
SC28L198
Octal UART for 3.3 V and 5 V supply voltage
2006 Aug 10
27
Table 22. XISR – Xon–Xoff Interrupt Status Register
Bits 7:6
Bits 5:4
Bits 3:2
Bits 1:0
Received X Character Sta-
tus
Automatic X Character transmis-
sion status
TxD flow status
TxD character status
00 – none
01 – Xoff received
10 – Xon received
11 – both received
00 – none
01 – Xon transmitted
10 – Xoff transmitted
11 – Illegal, does not occur
00 – normal
01 – TxD halt pending
10 – re–enabled
11 – flow disabled
00 – normal TxD data
01 – wait on normal data
10 – Xoff in pending
11 – Xon in pending
XISR[7:6] – Received X Character Status. This field can be read to
determine if the receiver has encountered an Xon or Xoff character
in the incoming data stream. These bits are maintained until a read
of the XISR. The field is updated by X character reception
regardless of the state of MR0(7, 3:2) or IMR(4). The field can
therefore be used as a character detector for the bit patterns stored
in the Xon and Xoff Character Registers.
XISR[5:4] – Automatic transmission Status. This field indicates the
last flow control character sent in the Auto Receiver flow control
mode. If Auto Receiver mode has not been enabled, this field will
always read b’00. It will likewise reset to b’00 if MR0(3) is reset. If
the Auto Receiver mode is exited while this field reads b’10, it is the
user’s responsibility to transmit an Xon, when appropriate.
XISR[3:2] – TxD flow Status. This field tracks the transmitter’s flow
status as follows:
00 – normal. The flow control is under host control.
01 – TxD halt pending. After the current character finishes the
transmitter will stop. The status will then change to b’00.
10 – re–enabled. The transmitter had been halted and restarted.
It is sending data characters. After a read of the XISR, it will
return to ”normal” status.
11 – disabled. The transmitter is flow controlled.
XISR[1:0] – TxD character Status. This field allows determination of
the type of character being transmitted. If XISR(1:0) is b’01, the
channel is waiting for a data character to transfer from the TxFIFO.
This condition will only occur for a bit time after an Xon or Xoff
character transmission unless the TxFIFO is empty.
Table 23. WDTRCR – Watch-dog Timer Enable
Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WDT
h
WDT
g
WDT
f
WDT
e
WDT
d
WDT
c
WDT
b
WDT
a
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
1 on
0 off
This register enables the watch-dog Timer for each of the 8
receivers on the Octal UART.
Table 24. BRGTRU
– BRG Timer Reload
Registers, Upper
Bits 7:0
8 MSB of the BRG Timer divisor.
This is the upper byte of the 16 bit value used by the BRG timer in
generating a baud rate clock
Table 25. BRGTRL
– BRG Timer Reload
Registers, Lower
Bits 7:0
8 LSB of the BRG Timer divisor.
This is the lower byte of the 16 bit value used by the BRG timer in
generating a baud rate clock.
Table 26. BRGTCR – BRG Timer Control Register (BRGTCR)
Bit 7
Bit 6:4
Bit 3
Bit 2:0
BRGTCR b, Register control
BRGTCR b, Clock selection
BRGTCR a, Register control
BRGTCR a, Clock selection
0 – Resets the timer register and
holds it stopped
1 – Allows the timer register to
run.
000 – Sclk / 16
001 – Sclk / 32
010 – Sclk/ 64
011 – Sclk / 128
100 – X1
101 – X1 / 2
110 – I/O1b
111 – GIN(1)
0 – Resets the timer register and
holds it stopped.
1 – Allows the timer register to
run.
000 – Sclk / 16
001 – Sclk / 32
010 – Sclk / 64
011 – Sclk / 128
100 – X1
101 – X1 / 2
110 – I/O1a
111 – GIN(0)
Start/Stop control and clock select register for the two BRG
counters. The clock selection is for the input to the counters. It is
that clock divided by the number represented by the BRGTU and
BRGTL the will be used as the 16x clock for the receivers and
transmitters. When the BRG timer Clock is selected for the
receiver(s) or transmitter(s) the receivers and transmitters will
consider it as a 16x clock and further device it by 16. In other words
the receivers and transmitters will always be in the 16x ode of
operation when the internal BRG timer is selected for their clock.
相关PDF资料 |
PDF描述 |
|---|---|
| V24B5H150BL3 | CONVERTER MOD DC/DC 5V 150W |
| V24B5H150BL | CONVERTER MOD DC/DC 5V 150W |
| V24B5H150B3 | CONVERTER MOD DC/DC 5V 150W |
| SCC2692AE1B44,551 | IC UART DUAL W/FIFO 44PLCC |
| SC16C754BIB80,551 | IC UART QUAD 64BYTE 80LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC28L198A1BE-S | 功能描述:UART 接口集成电路 3V-5V 8CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L198C1A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Octal UART for 3.3V and 5V supply voltage |
| SC28L201 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:3.3 V, 5 V UART, 3.125 Mbit/s, with 256-byte FIFO |
| SC28L201A1DGG | 功能描述:UART 接口集成电路 3-5V 1CH UART 3MBPS 256B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L201A1DGG,112 | 功能描述:UART 接口集成电路 3-5V 1CH UART 3MBPS RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。