参数资料
| 型号： | SC4508AMLTRT |
| 厂商： | Semtech |
| 文件页数： | 7/21页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST INV PWM 12-MLPQ |
| 标准包装： | 1 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.5MHz |
| 占空比： | 97% |
| 电源电压： | 2.7 V ~ 15 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 是 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 12-VQFN 裸露焊盘 |
| 包装： | 标准包装 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC4508AMLDKR |
SC4508A
POWER MANAGEMENT
Application Information (Cont.)
undergoes soft-start. If overload persists, the SC4508A
will undergo repetitive auto-shutdown-restart hiccup
I L ( pk ) = I O
1 V IN V O + V D
V IN + V O + V D
V IN
for Buck ? Boost
+
(
2 f s ? L V IN + V O + V D
)
mode.
In normal operation, the VREF voltage follows the SS/
EN voltage from 0 to 0.5V as the SS/EN voltage ramps
I O - full load current
V O - output voltage
V IN - input voltage
V D - diode forward voltage drop
f S - switching frequency
L - inductor
Error Amplifier
The error amplifier in the SC4508A is a transconductance
error amplifier, which is easily configured as a type two
compensator by connecting compensation network from
the COMP pin to AGND. The output voltage of the error
amplifier is compared to the sensed current signal
(amplified by gain 8) plus internal 500mV ramp to generate
duty cycle.
Both the non-inverting and the inverting inputs of the
error amplifier are brought out as device pins so that a
converter can be configured as either buck or buck-boost
converter.
Soft-Start and Overload Protection
The undervoltage lockout circuit discharges the SS/EN
capacitors. After V DD rises above 2.5V, the SS/EN
capacitors are slowly charged by internal 10uA current
source. As the SS/EN capacitor continues to be charged,
the VREF and the COMP voltage follows. The converter
gradually delivers increasing power to the output. The
inductor current follows the COMP voltage envelope until
the output goes into regulation.
After the SS/EN capacitor is charged above 1.4V (high
enough for the error amplifier to provide full load current),
the overload detection circuit is activated. If the CS pin
senses 32 consective switching cycles of over current,
the SC4508A will shut down and hold off the MOSFET
while discharging the soft-start capacitor. The SS/EN
capacitor is discharged with an internal 12mA current
sink. The overload latch is reset when the SS/EN capacitor
is discharged below 0.5V. The SS/EN capacitor is then
recharged with the 10μA current source and the converter
up from 1.4V to 1.9V. After the SS/EN voltage rises
above 1.9V, it settles at final value depending upon VDD.
If VDD higher than 7V, it is clamped around 6.8V. In the
worst case, the clamped voltage is about 10V. Therefore,
the external soft-start capacitor should be rated at least
16V.
The SS/EN pin can also be used as the enable input. The
MOSFET will be turned off if the SS/EN pin is pulled below
0.5V.
Converter Specifications
Buck or buck-boost converter design includes the
following specifications:
Input voltage range: V in ∈ [ V in , min , V in , max ]
Input voltage ripple (peak-to-peak): D V in
Output voltage: V o
Output voltage accuracy: e
Output voltage ripple (peak-to-peak): D V o
Nominal output (load) current: I o
Maximum output current limit: I o,max
Output (load) current transient slew rate: dI o (A/s)
Circuit efficiency: h
Selection criteria and design procedures for the
following are described.
1) output inductor ( L ) type and value
2) output capacitor ( C o ) type and value
3) input capacitor ( C in ) type and value
4) power MOSFETs
5) current sensing and limiting circuit
6) voltage sensing circuit
7) loop compensation network
Inductor (L) and Ripple Current
The output inductor selection/design is based on the
output DC and transient requirements. Both output
current and voltage ripples are reduced with larger
inductors but it takes longer to change the inductor
current during load transients. Conversely smaller
inductors results in lower DC copper losses but the AC
? 2007 Semtech Corp.
7
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC4517AIMSTRT | IC REG BUCK ADJ 1.5A 8MSOP |
| SC4518HSETRT | IC REG BUCK 2A 8-SOIC |
| SC4519HSETRT | IC REG BUCK 3A 8-SOIC |
| SC4524ASETRT | IC REG BUCK 2A 8SOIC |
| SC4524BSETRT | IC REG BUCK 2A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC4508IMLTRT | 制造商:Semtech Corporation 功能描述:DC/DC Converter (DC-DC) / Switching Regu |
| SC4509 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Highly Integrated Step-Up Converter for White LED Applications in MLPD-W8-2x2 |
| SC4509EVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Highly Integrated Step-Up Converter for White LED Applications in MLPD-W8-2x2 |
| SC4509SK.TRT | 制造商:SEMTECH 功能描述:I.C. |
| SC4509SKTRT | 功能描述:IC LED DRVR WT/OLED BCKLT SOT236 RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
发布紧急采购，3分钟左右您将得到回复。