参数资料
| 型号： | SC4518HSETRT |
| 厂商： | Semtech |
| 文件页数： | 9/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 2A 8-SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出数： | 1 |
| 输入电压： | 4.4 V ~ 24 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 600kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SO 裸露焊盘 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC4518HSEDKR |
SC4518H
POWER MANAGEMENT
Application Information (Cont.)
Input Capacitor Selection
The required minimum capacitance for the boost
capacitor will be:
The input capacitor selection is based on its ripple current
level, required capacitance and voltage rating. This
C boost =
I B
V D
? T W
V O ? ( V I ? V O )
I CIN ( RMS ) = I OMAX ?
C boost =
?
? D max =
?
? 0 . 85 = 128 nF
C IN = I OMAX ?
T W =
? D max
P total = I o ? R on ? D + 10 . 8 ? 10 ? 3 ? I o ? V I +
? I o ? D ? ( V boost )
capacitor must be able to provide the ripple current by
the switching actions. For the continuous conduction
mode, the RMS value of the input capacitor current
I CIN(RMS) can be calculated from:
V 2 I
This current gives the capacitor’s power loss through its
R CIN(ESR) as follows:
P CIN = I 2 CIN ( RMS ) ? R CIN ( ESR )
The input ripple voltage mainly depends on the input
capacitor’s ESR and its capacitance for a given load, input
voltage and output voltage. Assuming that the input
current of the converter is constant, the required input
capacitance for a given voltage ripple can be calculated
by:
D ? ( 1 ? D )
fs ? ( ? V I ? I OMAX ? R CIN ( ESR ) )
Where:
? V I = the given input voltage ripple.
Because the input capacitor is exposed to the large surge
current, attention is needed for the input capacitor. If
tantalum capacitors are used at the input side of the
converter, one needs to ensure that the RMS and surge
ratings are not exceeded. For generic tantalum
capacitors, it is suggested to derate their voltage ratings
at a ratio of about two to protect these input capacitors.
Boost Capacitor and its Supply Source Selection
The boost capacitor selection is based on its discharge
ripple voltage, worst case conduction time and boost
current. The worst case conduction time T w can be
estimated as follows:
1
f s
Where:
f s = the switching frequency and
Dmax = maximum duty ratio, 0.85 for the SC4518H.
Where:
I B = the boost current and
V D = discharge ripple voltage.
With f s = 600kHz, V D = 0.5V and I B =0.045A, the required
minimum capacitance for the boost capacitor is:
I B 1 0 . 045 1
V D f s 0 . 5 600 k
The internal driver of the switch requires a minimum 2.7V
to fully turn on that switch to reduce its conduction loss.
If the output voltage is less than 2.7V, the boost capacitor
can be connected to either the input side or an
independent supply with a decoupling capacitor. But the
Pin BST should not see a voltage higher than its maximum
rating.
Freewheeling Diode Selection
This diode conducts during the switch’s off-time. The diode
should have enough current capability for full load and
short circuit conditions without any thermal concerns.
Its maximum repetitive reverse block voltage has to be
higher than the input voltage of the SC4518H. A low
forward conduction drop is also required to increase the
overall efficiency. The freewheeling diode should be
turned on and off fast with minimum reverse recovery
because the SC4518H is designed for high frequency
applications. SS13 Schottky rectifier is recommended
for certain applications. The average current of the diode,
I D _ AVG can be calculated by:
I D _ AVG = I O max ? ( 1 ? D )
Thermal Considerations
There are three major power dissipation sources for the
SC4518H. The internal switch conduction loss, its
switching loss due to the high frequency switching actions
and the base drive boost circuit loss. These losses can
be estimated as:
2 10
500
? 2007 Semtech Corp.
9
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC4519HSETRT | IC REG BUCK 3A 8-SOIC |
| SC4524ASETRT | IC REG BUCK 2A 8SOIC |
| SC4524BSETRT | IC REG BUCK 2A 8SOIC |
| SC4524CSETRT | IC REG BUCK ADJ 2A 8SOIC |
| SC4524DSETRT | IC REG BUCK ADJ 2A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC4518ISTRT | 制造商:Semtech Corporation 功能描述:Conv DC-DC Single Step Down 3V to 16V 8-Pin SOIC T/R 制造商:Semtech Corporation 功能描述:IC 1.5 AMP STP DWN SWTCH REG 制造商:Semtech Corporation 功能描述:Voltage Regulator IC Leaded Process Comp 制造商:Semtech Corporation 功能描述:SC Series 3 to 16 V 600 kHz SMT Step-Down Switching Regulator - SOIC-8LEDP |
| SC4519 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:600kHz, 3A Step-Down Switching Regulator |
| SC4519ASETRT | 制造商:Semtech Corporation 功能描述: |
| SC4519H | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:600kHz, 3A Step-Down Switching Regulator |
| SC4519H_07 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:600kHz, 3A Step-Down Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。