参数资料
| 型号： | SC4519HSETRT |
| 厂商： | Semtech |
| 文件页数： | 11/14页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3A 8-SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出数： | 1 |
| 输入电压： | 4.4 V ~ 24 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 600kHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SO 裸露焊盘 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC4519HSEDKR |
SC4519H
POWER MANAGEMENT
Application Information (Cont.)
Mag
Loop gain T(s)
Layout Guidelines:
In order to achieve optimal electrical and thermal
performance for high frequency converters, special
ω p1
ω Z
Power stage
ω C ω P2
ω
attention must be paid to the PCB layouts. The goal of
layout optimization is to identify the high di/dt loops and
minimize them. The following guidelines should be used
to ensure proper operation of the converters.
1. A ground plane is suggested to minimize switching
noises and trace losses and maximize heat
Figure 4. Asymptotic diagrams of power stage with
current loop closed and its loop gain.
The design guidelines for the SC4519H applications are
as following:
1. Set the loop gain crossover corner frequency ω C for
given switching corner frequency ω C = 2 π f C
2. Place an integrator at the origin to increase DC and
low frequency gains.
3. Select ω Z such that it is placed at ω P1 to obtain a
-20dB/dec rate to go across the 0dB line.
4. Place a high frequency compensator pole
ω P2 ( ω P2 = π f s ) to get the maximum attenuation of
the switching ripple and high frequency noise with
the adequate phase lag at ω C.
transferring.
2. Start the PCB layout by placing the power components
first. Arrange the power circuit to achieve a clean
power flow route. Put all power connections on one
side of the PCB with wide copper filled areas if
possible.
3. The V IN bypass capacitor should be placed next to
the V IN and GND pins.
4. The trace connecting the feedback resistors to the
output should be short, direct and far away from any
noise sources such as switching node and switching
components.
5. Minimize the loop including input capacitor, the
SC4519H and freewheeling diode D 2 . This loop
passes high di/dt current. Make sure the trace width
is wide enough to reduce copper losses in this loop.
6. Maximize the trace width of the loop connecting the
inductor, freewheeling diode D 2 and the output
capacitor.
7. Connect the ground of the feedback divider and the
compensation components directly to the GND pin
of the SC4519H by using a separate ground trace.
8. Connect Pin 4 to a large copper area to remove the
IC heat and increase the power capability of the
SC4519H. A few feedthrough holes are required to
connect this large copper area to a ground plane to
further improve the thermal environment of the
SC4519H. The traces attached to other pins should
be as wide as possible for the same purpose.
? 2007 Semtech Corp.
11
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC4524ASETRT | IC REG BUCK 2A 8SOIC |
| SC4524BSETRT | IC REG BUCK 2A 8SOIC |
| SC4524CSETRT | IC REG BUCK ADJ 2A 8SOIC |
| SC4524DSETRT | IC REG BUCK ADJ 2A 8SOIC |
| SC4524SETRT | IC REG BUCK 2A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC4519S.TRT | 制造商:SEMTECH 功能描述:I.C. |
| SC4519STRT | 制造商:Semtech Corporation 功能描述:Conv DC-DC Single Step Down 16V 8-Pin SOIC T/R 制造商:Semtech Corporation 功能描述:SC4519 Series 16 V 600 kHz 3 A SMT Step-Down Switching Regulator - SOIC-8LEDP |
| SC451ITSTRT | 制造商:Semtech Corporation 功能描述: |
| SC451XX | 制造商:未知厂家 制造商全称:未知厂家 功能描述:LI-ION BATTERY PROTECTOR |
| SC452 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual-Phase Single Chip IMVP-6 Vcore Power Supply |
发布紧急采购，3分钟左右您将得到回复。