参数资料
| 型号： | SC4519HSETRT |
| 厂商： | Semtech |
| 文件页数： | 9/14页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3A 8-SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出数： | 1 |
| 输入电压： | 4.4 V ~ 24 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 600kHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SO 裸露焊盘 |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC4519HSEDKR |
SC4519H
POWER MANAGEMENT
Application Information (Cont.)
I CIN (RMS) = I OMAX ?
V
C boost =
?
? D max =
?
? 0.85 = 128nF
C IN = I OMAX ?
T W =
? D max
P total = I o ? R on ? D + 10.8 ? 10 ? 3 ? I o ? V I +
? I o ? D ? (V boost )
C boost =
? T W
capacitor must be able to provide the ripple current
drawn by the converter. For the continuous conduction
mode, the RMS value of the input capacitor current
I CIN(RMS) can be calculated from:
V O ? (V I ? V O )
2
I
This current gives the capacitor’s power loss through its
R CIN(ESR) as follows:
P CIN = I 2 CIN (RMS) ? R CIN(ESR)
The input ripple voltage mainly depends on the input
capacitor’s ESR and its capacitance for a given load, input
voltage and output voltage. Assuming that the input
current of the converter is constant, the required input
capacitance for a given voltage ripple can be calculated
by:
D ? (1 ? D)
fs ? ( ? V I ? I OMAX ? R CIN (ESR) )
Where:
? V I = the given input voltage ripple.
Because the input capacitor is exposed to the large surge
current, attention is needed for the input capacitor. If
tantalum capacitors are used at the input side of the
converter, one needs to ensure that the RMS and surge
ratings are not exceeded. For generic tantalum
capacitors, it is suggested to derate their voltage ratings
at a ratio of about two to protect these input capacitors.
Boost Capacitor and its Supply Source Selection
The boost capacitor selection is based on its discharge
ripple voltage, worst case conduction time and boost
current. The worst case conduction time T w can be
estimated as follows:
1
f s
Where:
f s = the switching frequency and
Dmax = maximum duty ratio, 0.85 for the SC4519H.
The required minimum capacitance for the boost
capacitor will be:
I B
V D
Where:
I B = the boost current and
V D = discharge ripple voltage.
With f s = 600kHz, V D = 0.5V and I B =0.045A, the required
minimum capacitance for the boost capacitor is:
I B 1 0.045 1
V D f s 0.5 600k
The internal driver of the switch requires a minimum 2.7V
to fully turn on that switch to reduce its conduction loss.
If the output voltage is less than 2.7V, the boost capacitor
can be connected to either the input side or an
independent supply with a decoupling capacitor. But the
Pin BST should not see a voltage higher than its maximum
rating.
Freewheeling Diode Selection
This diode conducts during the switch’s off-time. The diode
should have enough current capability for full load and
short circuit conditions without any thermal concerns.
Its maximum repetitive reverse block voltage has to be
higher than the input voltage of the SC4519H. A low
forward conduction drop is also required to increase the
overall efficiency. The freewheeling diode should be
turned on and off fast with minimum reverse recovery
because the SC4519H is designed for high frequency
applications. SS23 Schottky rectifier is recommended
for certain applications. The average current of the diode,
I D _ AVG can be calculated by:
I D - AVG = I omax ? ( I ? D )
Thermal Considerations
There are three major power dissipation sources for the
SC4519H. The internal switch conduction loss, its
switching loss due to the high frequency switching actions
and the base drive boost circuit loss. These losses can
be estimated as:
2 10
1000
Where:
I O = load current;
R on = on-equivalent resistance of the switch;
V BOOST = input voltage or output based on the boost circuit
connection.
? 2007 Semtech Corp.
9
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| SC4524ASETRT | IC REG BUCK 2A 8SOIC |
| SC4524BSETRT | IC REG BUCK 2A 8SOIC |
| SC4524CSETRT | IC REG BUCK ADJ 2A 8SOIC |
| SC4524DSETRT | IC REG BUCK ADJ 2A 8SOIC |
| SC4524SETRT | IC REG BUCK 2A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC4519S.TRT | 制造商:SEMTECH 功能描述:I.C. |
| SC4519STRT | 制造商:Semtech Corporation 功能描述:Conv DC-DC Single Step Down 16V 8-Pin SOIC T/R 制造商:Semtech Corporation 功能描述:SC4519 Series 16 V 600 kHz 3 A SMT Step-Down Switching Regulator - SOIC-8LEDP |
| SC451ITSTRT | 制造商:Semtech Corporation 功能描述: |
| SC451XX | 制造商:未知厂家 制造商全称:未知厂家 功能描述:LI-ION BATTERY PROTECTOR |
| SC452 | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:Dual-Phase Single Chip IMVP-6 Vcore Power Supply |
发布紧急采购，3分钟左右您将得到回复。