- 您现在的位置：买卖IC网 > PDF目录11822 > SCC2692AC1N28,129 (NXP Semiconductors)IC DUART 28-DIP PDF资料下载
参数资料
| 型号： | SCC2692AC1N28,129 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 26/30页 |
| 文件大小： | 0K |
| 描述： | IC DUART 28-DIP |
| 标准包装： | 13 |
| 特点： | 故障启动位检测 |
| 通道数： | 2，DUART |
| FIFO's： | 3 位 |
| 电源电压： | 5V |
| 带并行端口： | 是 |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 通孔 |
| 封装/外壳： | 28-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 28-DIP |
| 包装： | 管件 |
| 其它名称： | 933981720129 SCC2692AC1N28-S SCC2692AC1N28-S-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页
Philips Semiconductors
Product specification
SCC2692
Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
5
PIN DESCRIPTION
SYMBOL
APPLICABLE
TYPE
NAME AND FUNCTION
SYMBOL
40,44
28
TYPE
NAME AND FUNCTION
D0-D7
X
I/O
Data Bus: Bidirectional 3-State data bus used to transfer commands, data and status between the
DUART and the CPU. D0 is the least significant bit.
CEN
X
I
Chip Enable: Active-Low input signal. When Low, data transfers between the CPU and the DUART
are enabled on D0-D7 as controlled by the WRN, RDN and A0-A3 inputs. When High, places the
D0-D7 lines in the 3-State condition.
WRN
X
I
Write Strobe: When Low and CEN is also Low, the contents of the data bus are loaded into the
addressed register. The transfer occurs on the rising edge of the signal.
RDN
X
I
Read Strobe: When Low and CEN is also Low, causes the contents of the addressed register to be
presented on the data bus. The read cycle begins on the falling edge of RDN.
A0-A3
X
I
Address Inputs: Select the DUART internal registers and ports for read/write operations.
RESET
X
I
Reset: A High level clears internal registers (SRA, SRB, IMR, ISR, OPR, OPCR), puts OP0-OP7 in
the High state, stops the counter/timer, and puts Channels A and B in the inactive state, with the TxDA
and TxDB outputs in the mark (High) state. Resets Test modes, MR pointer set to MR1.
INTRN
X
O
Interrupt Request: Active-Low, open-drain, output which signals the CPU that one or more of the
eight maskable interrupting conditions are true.
X1/CLK
X
I
Crystal 1: Crystal connection or an external clock input. A crystal of a clock the appropriate frequency
(nominally 3.6864 MHz) must be supplied at all times. For crystal connections see Figure 7, Clock Timing.
X2
X
I
Crystal 2: Crystal connection. See Figure 7. If a crystal is not used it is best to keep this pin not
connected although it is permissible to ground it.
RxDA
X
I
Channel A Receiver Serial Data Input: The least significant bit is received first. “Mark” is High,
“space” is Low.
RxDB
X
I
Channel B Receiver Serial Data Input: The least significant bit is received first. “Mark” is High,
“space” is Low.
TxDA
X
O
Channel A Transmitter Serial Data Output: The least significant bit is transmitted first. This output is
held in the “mark” condition when the transmitter is disabled, idle or when operating in local loopback
mode. “Mark” is High, “space” is Low.
TxDB
X
O
Channel B Transmitter Serial Data Output: The least significant bit is transmitted first. This output
is held in the ‘mark’ condition when the transmitter is disabled, idle, or when operating in local
loopback mode. ‘Mark’ is High, ‘space’ is Low.
OP0
X
O
Output 0: General purpose output or Channel A request to send (RTSAN, active-Low). Can be
deactivated automatically on receive or transmit.
OP1
X
O
Output 1: General purpose output or Channel B request to send (RTSBN, active-Low). Can be
deactivated automatically on receive or transmit.
OP2
X
O
Output 2: General purpose output, or Channel A transmitter 1X or 16X clock output, or Channel A
receiver 1X clock output.
OP3
X
O
Output 3: General purpose output or open-drain, active-Low counter/timer output or Channel B
transmitter 1X clock output, or Channel B receiver 1X clock output.
OP4
X
O
Output 4: General purpose output or Channel A open-drain, active-Low, RxRDYAN/FFULLAN output.
OP5
X
O
Output 5: General purpose output or Channel B open-drain, active-Low, RxRDYBN/FFULLBN output.
OP6
X
O
Output 6: General purpose output or Channel A open-drain, active-Low, TxRDYAN output.
OP7
X
O
Output 7: General purpose output, or Channel B open-drain, active-Low, TxRDYBN output.
IP0
X
I
Input 0: General purpose input or Channel A clear to send active-Low input (CTSAN). Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP1
X
I
Input 1: General purpose input or Channel B clear to send active-Low input (CTSBN). Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP2
X
I
Input 2: General purpose input or counter/timer external clock input. Pin has an internal VCC pull-up
device supplying 1 to 4
mA of current.
IP3
X
I
Input 3: General purpose input or Channel A transmitter external clock input (TxCA). When the
external clock is used by the transmitter, the transmitted data is clocked on the falling edge of the
clock. Pin has an internal VCC pull-up device supplying 1 to 4 mA of current.
IP4
X
I
Input 4: General purpose input or Channel A receiver external clock input (RxCA). When the external
clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
IP5
X
I
Input 5: General purpose input or Channel B transmitter external clock input (TxCB). When the
external clock is used by the transmitter, the transmitted data is clocked on the falling edge of the
clock. Pin has an internal VCC pull-up device supplying 1 to 4 mA of current.
IP6
X
I
Input 6: General purpose input or Channel B receiver external clock input (RxCB). When the external
clock is used by the receiver, the received data is sampled on the rising edge of the clock. Pin has an
internal VCC pull-up device supplying 1 to 4 mA of current.
VCC
X
I
Power Supply: +5V supply input.
GND
X
I
Ground
相关PDF资料 |
PDF描述 |
|---|---|
| SCC2692AC1A44,529 | IC DUART SOT187-2 |
| VI-B5D-IY | CONVERTER MOD DC/DC 85V 50W |
| SC26C92C1A,529 | IC DUART SOT187-2 |
| SC16C554BIBM,128 | IC UART QUAD SOT414-1 |
| SCC68692E1A44,518 | IC DUART 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SCC2692AC1N28-S | 功能描述:UART 接口集成电路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SCC2692AC1N40 | 制造商:NXP Semiconductors 功能描述:IC DUART 2692 DIP40 制造商:NXP Semiconductors 功能描述:IC, DUART, 2692, DIP40 制造商:NXP Semiconductors 功能描述:IC, DUAL UART, FIFO, 115KBAUD 5.5V DIP40; No. of Channels:2; Data Rate:1Mbps; Supply Voltage Min:4.5V; Supply Voltage Max:5.5V; Digital IC Case Style:DIP; No. of Pins:40; Operating Temperature Min:0C; Operating Temperature Max:70C ;RoHS Compliant: Yes |
| SCC2692AC1N40,602 | 功能描述:UART 接口集成电路 2CH. 5V IND. UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SCC2692AC1N40602 | 制造商:NXP Semiconductors 功能描述:IC DUAL UART FIFO 1MBPS 5.5V DIP-40 |
| SCC2692AE1A44 | 功能描述:UART 接口集成电路 5V INDSTRL UART 2 C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。