- 您现在的位置：买卖IC网 > PDF目录11819 > SCC2698BE1A84,518 (NXP Semiconductors)IC UART OCTAL ENHANCED 84-PLCC PDF资料下载
参数资料
| 型号： | SCC2698BE1A84,518 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 26/29页 |
| 文件大小： | 0K |
| 描述： | IC UART OCTAL ENHANCED 84-PLCC |
| 标准包装： | 250 |
| 特点： | 故障启动位检测 |
| 通道数： | 8 |
| FIFO's： | 3 位 |
| 电源电压： | 5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 84-LCC（J 形引线） |
| 供应商设备封装： | 84-PLCC |
| 包装： | 带卷 (TR) |
| 其它名称： | 935056380518 SCC2698BE1A84-T SCC2698BE1A84-T-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页
Philips Semiconductors
Product data sheet
SCC2698B
Enhanced octal universal asynchronous
receiver/transmitter (Octal UART)
2006 Aug 07
6
PIN DESCRIPTION (Continued)
MNEMONIC
PIN
TYPE
NAME AND FUNCTION
MNEMONIC
PIN
NO.
TYPE
NAME AND FUNCTION
MPI1a–MPI1h
14, 21,
38, 40,
60, 62,
78, 80
I
Multi-Purpose Input 1: This pin (one for each UART) is programmable. Its state can always be
determined by reading the IPCR bit 1 or IPR bit 1.
C/TCLK – This input will serve as the external clock for the counter/timer when ACR[5] is set to 0.
This occurs only for channels a, c, e, and g since there is one counter/timer for each DUART block.
This pin is provided with a change-of-state detector.
MPP1a–MPP1h
24, 26,
42, 44,
64, 66,
82, 84
I/O
Multi-Purpose Pin 1: This pin (one for each UART) is programmed to be an input or an output
according to the state of OPCR[7]. (0 = input, 1 = output). The state of the multi-purpose pin can
always be determined by reading the IPR. When programmed as an input, it will be the transmitter
clock (TxCLK). It will be 1x or 16x according to the clock select registers (CSR[3.0]). When
programmed as an output, it will be the status register TxRDY bit. These pins have a small pull-up
device.
MPP2a–MPP2h
28, 30,
48, 50,
68, 70,
2, 4
I/O
Multi-Purpose Pin 2: This pin (one for each UART) is programmed to be an input or an output
according to the state of OPCR[7]. (0 = input, 1 = output). The state of the multi-purpose pin can
always be determined by reading the IPR. When programmed as an input, it will be the receiver clock
(RxCLK). It will be 1x or 16x according to the clock select registers (CSR[7:4). When programmed as
an output, it will be the ISR status register RxRDY/FIFO full bit. These pins have a small pull-up
device.
Test Input
–
I
Test Input: This pin is used as an input for test purposes at the factory while in test mode. This pin
can be treated as ‘N/C’ by the user. It can be tied high, or left open.
VCC
5, 45
I
Power Supply: +5V supply input.
GND
20, 65
I
Ground
BLOCK DIAGRAM
As shown in the block diagram, the Octal UART consists of: data
bus buffer, interrupt control, operation control, timing, and eight
receiver and transmitter channels. The eight channels are divided
into four different blocks, each block independent of each other (see
Figure 3). Figure 2 represents the DUART block.
BLOCK A
CHANNELS a, b
BLOCK C
CHANNELS e, f
BLOCK D
CHANNELS g, h
BLOCK B
CHANNELS c, d
SD00186
Figure 3. Channel Architecture
Channel Blocks
There are four blocks (Figure 3), each containing two sets of
receiver/transmitters. In the following discussion, the description
applies to Block A which contains channels a and b. However, the
same information applies to all channel blocks.
Data Bus Buffer
The data bus buffer provides the interface between the external and
internal data buses. It is controlled by the operation control block to
allow read and write operations to take place between the controlling
CPU and the Octal UART.
Interrupt Control
A single interrupt output per DUART (INTRN) is provided which is
asserted on occurrence of any of the following internal events:
–Transmit holding register ready for each channel
–Receive holding register ready or FIFO full for each channel
–Change in break received status for each channel
–Counter reached terminal count
–Change in MPI input
Associated with the interrupt system are the interrupt mask register
(IMR) and the interrupt status register (ISR). The IMR can be
programmed to select only certain conditions, of the above, to cause
INTRN to be asserted. The ISR can be read by the CPU to
determine all currently active interrupting conditions. However, the
bits of the ISR are not masked by the IMR. The transmitter ready
status and the receiver ready or FIFO full status can be provided on
MPP1a, MPP1b, MPP2a, and MPP2b by setting OPCR[7]. these
outputs are not masked by IMR.
Operation Control
The operation control logic receives operation commands from the
CPU and generates appropriate signals to internal sections to
control device operation. It contains address decoding and read and
write circuits to permit communications with the microprocessor via
the data bus buffer. The functions performed by the CPU read and
write operations are shown in Table 1.
Mode registers 1 and 2 are accessed via an auxiliary pointer. The
pointer is set to MR1 by RESET or by issuing a reset pointer
command via the command register. Any read or write of the mode
register while the pointer is at MR1 switches the pointer to MR2 after
the read or write. The pointer then remains at MR2 so that
subsequent accesses are to MR2. To access MR1, the command
0001 of the command register must be executed.
Timing Circuits
The timing block consists of a crystal oscillator, a baud rate
generator, a programmable 16-bit counter/timer for each block, and
two clock selectors.
Crystal Clock
The crystal oscillator operates directly from a 3.6864MHz crystal
connected across the X1/ CLK and X2 inputs with a minimum of
external components. If an external clock of the appropriate
frequency is available, it may be connected to X1/CLK. If an external
相关PDF资料 |
PDF描述 |
|---|---|
| SC28L92A1B,551 | IC UART DUAL W/FIFO 44PQFP |
| SC16C754BIA68,529 | IC UART QUAD 64BYTE 68PLCC |
| V24B5H150BF2 | CONVERTER MOD DC/DC 5V 150W |
| SCC2698BC1A84,518 | IC UART OCTAL ENHANCED SOT189 |
| SC28L198A1A,518 | IC UART OCTAL SOT189-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SCC2698BE1A84-T | 功能描述:UART 接口集成电路 5V INDSTRL UART 8 C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SCC290 | 功能描述:仪表保护和存储 Software, carrying case kit 190 Series RoHS:否 制造商:Fluke |
| SCC298 | 制造商:Fluke Electronics 功能描述:AUTO TROUBLE KIT 190-SERIES-II 制造商:Fluke Electronics 功能描述:AUTOMOTIVE TROUBLESHOOTING KIT 190-SERIES-II |
| SCC3.0 | 制造商:Russell 功能描述: |
| SCC30 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Pressure Sensors |
发布紧急采购，3分钟左右您将得到回复。