- 您现在的位置：买卖IC网 > Datasheet目录251 > SFCF64GBH2BU4TO-I-NU-517-STD (Swissbit NA Inc)FLASH SLC UDMA/MDMA/PIO 64GB Datasheet资料下载
参数资料
| 型号： | SFCF64GBH2BU4TO-I-NU-517-STD |
| 厂商： | Swissbit NA Inc |
| 文件页数： | 8/102页 |
| 文件大小： | 0K |
| 描述： | FLASH SLC UDMA/MDMA/PIO 64GB |
| 标准包装： | 1 |
| 系列： | C-440 |
| 存储容量： | 64GB |
| 存储器类型： | CompactFlash? |
| 其它名称： | 1052-1090 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页
Requirements for using extended speed (PIO 5, 6/ MDMA 3, 4)
(CompactFlash TM Specification 5.0; section 4.3.7)
The CF Advanced Timing modes include PCMCIA I/O and Memory modes that are 100ns or faster and True IDE PIO
Modes 5, 6 and Multiword DMA Modes 3, 4.
When operating in CF Advanced timing modes, the host shall conform to the following requirements:
1.
2.
Only one CF device shall be attached to the CF Bus.
The host shall not present a load of more than 40pF to the device for all signals, including any cabling.
3. The maximum cable length is 0.05 m (2 in). The cable length is measured from the card connector to the
host controller. 0.46 m (18 in) cables are not supported .
4. The – WAIT and IORDY signals shall be ignored by the host.
Devices supporting CF Advanced timing modes shall also support slower timing modes, to ensure operability with
systems that do not support CF Advanced timing modes.
Ultra DMA Electrical Requirements
(CompactFlash TM Specification 5.0; section 4.3.8)
Operation in Ultra DMA mode requires careful attention to cabling, printed circuit board (PCB) trace routing and
termination for reliable operation. These requirements are described in the following sections.
Host and Card signal capacitance limits for Ultra DMA operation
The host interface signal capacitance at the host connector shall be a maximum of 25pF for each signal as
measured at 1 MHz.
The card interface signal capacitance at the card connector shall be a maximum of 20pF for each signal as
measured at 1 MHz.
Series termination required for Ultra DMA operation
Series termination resistors are required at both the host and the card for operation in any of the Ultra DMA
modes. The CF specification describes typical values for series termination at the host and the device.
C-400 cards have the specified serial resistances in IDE bus.
4.2 Environmental Specifications
4.2.1 Recommended Operating Conditions
Table 3: CF Card Recommended Operating Conditions
Parameter
Commercial Operating Temperature
Industrial Operating Temperature
Power Supply VCC Voltage (5V)
Power Supply VCC Voltage (3.3V)
*) Voltage could be between 3.1V and 5.5V
Table 4: Current consumption (1)
Value
0°C to 70°C
-40°C to 85°C
4.5V to 5.5V – 5.0V ±10% *)
3.13V to 3.46V – 3.3V ±5% *)
Current Consumption (typ)
Read (UDMA6/max)
Write (UDMA6/max)
Sleep/Idle Mode (typ/max)
3.3V
110 / 140
90 / 110
3/5
5V
110 / 140
85 / 110
3/5
Unit
mA
1.
All values are typical at 25° C and nominal supply voltage and refer to 8Gbyte CompactFlash TM Card.
Max values are for 32GB cards in UDMA6 mode in IDE mode.
The card goes to Sleep/idle mode 20ms (default) after last host command.
The sleep current at 5V depends on the signal level at the CF-Bus
4.2.2 Recommended Storage Conditions
Table 5: CF Card Recommended Storage Conditions
Parameter
Storage Temperature
High temperature storage decreases the data retention.
Value
-50°C to 100°C
Swissbit AG
Industriestrasse 4
Swissbit reserves the right to change products or specifications without notice.
Revision: 1.00
CH-9552 Bronschhofen
Switzerland
www.swissbit.com
industrial@swissbit.com
C-440_data_sheet_CF-HxBU_Rev100.doc
Page 8 of 102
相关PDF资料 |
PDF描述 |
|---|---|
| SFN08B4702CBQLF7 | RES ARRAY 47K OHM 7 RES 8-DFN |
| SFP1050-12BG | FRONT END AC/DC 1050W 12V |
| SFP450-12BG | PWR SUP 450W 12V 36.6A W/STANDBY |
| SFSD1024N1BN1TO-I-DF-151-STD | FLASH MICRO SD CARD IND S-200 1G |
| SFSD2048L1BN2TO-I-DF-151-STD | FLASH SECURE DGTL CARD SD 2G |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SFCF64GBH2BU4TO-I-NU-527-STD | 制造商:SWISSBIT 功能描述:CFC C-440 DENSITY INDUSTRIAL - Trays 制造商:SWISSBIT NA INC 功能描述:FLASH CARD 64GB IND C-440 制造商:Swissbit 功能描述:Memory Cards 64GB IND COMPACT FLASH SLC NAND C440 |
| SFCF8192H1BO2TO-C-Q1-523-SMA | 制造商:SWISSBIT NA INC 功能描述:FLASH |
| SFCF8192H1BO2TO-C-Q1-533-ZP1 | 制造商:SWISSBIT NA INC 功能描述:FLASH |
| SFCF8192H1BO2TO-C-Q1-543-SMA | 制造商:SWISSBIT NA INC 功能描述:FLASH |
| SFCF8192H1BO2TOIQ1523SMA | 制造商:Swissbit 功能描述:Flash Card 8G-Byte 3.3V/5V CompactFlash 50-Pin |
发布紧急采购，3分钟左右您将得到回复。