- 您现在的位置：买卖IC网 > PDF目录10989 > SI3216M-GT (Silicon Laboratories Inc)IC SLIC/CODEC 1CH 38TSSOP PDF资料下载
参数资料
| 型号： | SI3216M-GT |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 44/122页 |
| 文件大小： | 0K |
| 描述： | IC SLIC/CODEC 1CH 38TSSOP |
| 标准包装： | 50 |
| 系列： | ProSLIC® |
| 功能： | 用户线路接口概念（SLIC），CODEC |
| 接口： | GCI，PCM，SPI |
| 电路数： | 1 |
| 电源电压： | 3.13 V ~ 5.25 V |
| 电流 - 电源： | 88mA |
| 功率（瓦特）： | 700mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 管件 |
| 包括： | 音频音调生成，BORSCHT 功能，FSK 生成，振铃和电池电压生成 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页
Si3216
28
Rev. 1.0
Not
Recommended
fo
r N
ew
D
esi
gn
s
2.1.2. Linefeed Architecture
The ProSLIC is a low-voltage CMOS device that uses
either an Si3201 linefeed interface IC or low-cost
external components to control the high voltages
required for subscriber line interfaces. Figure 17 is a
simplified illustration of the linefeed control loop circuit
for TIP or RING and the external components used.
The ProSLIC uses both voltage and current sensing to
control TIP and RING. DC and ac line voltages on TIP
and RING are measured through sense resistors RDC
and RAC, respectively. The ProSLIC uses linefeed
transistors QP and QN to drive TIP and RING. QDN
isolates the high-voltage base of QN from the ProSLIC.
The ProSLIC measures voltage at various nodes in
order to monitor the linefeed current. RDC, RSE, and
RBAT provide access to these measuring points. The
sense circuitry is calibrated on-chip to guarantee
measurement
accuracy
with
standard
external
component tolerances. See 2.1.9."Linefeed Calibration"
on page 33 for details.
2.1.3. Linefeed Operation States
The ProSLIC linefeed has eight states of operation as
shown in Table 22. The state of operation is controlled
using the Linefeed Control register (direct Register 64).
The Open state turns off all currents into the external
bipolar transistors and can be used in the presence of
fault conditions on the line and to generate Open Switch
Intervals (OSIs). TIP and RING are tri-stated with a dc
output impedance of about 150 k
. The ProSLIC can
also automatically enter the Open state if it detects
excessive power being consumed in the external bipolar
transistors. See 2.1.5."Power Monitoring and Line Fault
Detection" on page 30 for more details.
In the Forward Active and Reverse Active states,
linefeed circuitry is on, and the audio signal paths are
disabled.
In
the
forward
and
reverse
on-hook
transmission states, audio signal paths are enabled to
provide data transmission during an on-hook loop
condition.
The TIP Open state turns off all control currents to the
external bipolar devices connected to TIP and provides
an active linefeed on RING for ground start operation.
The RING Open state provides similar operation with
the RING drivers off and TIP active.
The
Ringing
state
drives
programmable
ringing
waveforms onto the line.
2.1.4. Loop Voltage and Current Monitoring
The ProSLIC continuously monitors the TIP and RING
voltages and external BJT currents. These values are
available in registers 78–89. Table 23 on page 30 lists
the values that are measured and their associated
registers. An internal A/D converter samples the
measured voltages and currents from the analog sense
circuitry and translates them into the digital domain. The
A/D updates the samples at an 800 Hz rate. Two
derived values are also reported—loop voltage and loop
current. The loop voltage, VTIP –VRING, is reported as a
1-bit sign, 6-bit magnitude format. For ground start
operation, the reported value is the RING voltage. The
loop current, (IQ1 – IQ2 + IQ5 –IQ6)/2, is reported in a 1-
bit sign, 6-bit magnitude format. In RING open and TIP
Open states, the loop current is reported as (IQ1 – IQ2) +
(IQ5 –IQ6).
相关PDF资料 |
PDF描述 |
|---|---|
| SI3216M-KT | IC SLIC/CODEC 1CH 38TSSOP |
| SI3210M-KT | IC SLIC/CODEC PROG 1CH 38TSSOP |
| S9S12P96J0MQK | MCU 96K FLASH AUTO 80-QFP |
| SI3201-BS | IC LINEFEED INTRFC SI321X 16SOIC |
| SI3200-KS | IC LINEFEED INTRFC 100V 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3216M-KT | 功能描述:IC SLIC/CODEC 1CH 38TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 电信 系列:ProSLIC® 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 06/Feb/2012 标准包装:750 系列:* |
| SI3216MPPQ1-EVB | 功能描述:音频 IC 开发工具 Si3216M QFN Eval RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| Si3216MPPQX-EB | 功能描述:拨号开发工具 QFN EVB w/ discrete Line Interface RoHS:否 制造商:Multi-Tech Systems 产品:Development Kits 类型:RJ Modems 工具用于评估:MT5656RJ 数据速率:115.2 kbps 接口类型:RJ-11, RS-232 工作电源电压:3.3 V, 5 V |
| SI3216MPPQX-EVB | 功能描述:音频 IC 开发工具 Si3216M QFN Eval Board RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| SI3216MPPT1-EVB | 功能描述:BOARD EVAL W/SI3201 INTERFACE RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
发布紧急采购，3分钟左右您将得到回复。