- 您现在的位置：买卖IC网 > PDF目录368620 > SI8250 (Silicon Laboratories Inc.) DIGITAL POWER CONTROLLER PDF资料下载
参数资料
| 型号： | SI8250 |
| 厂商： | Silicon Laboratories Inc. |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | DIGITAL POWER CONTROLLER |
| 中文描述： | 数字化电源控制器 |
| 文件页数： | 17/30页 |
| 文件大小： | 932K |
| 代理商： | SI8250 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Si8250/1/2
Preliminary Rev. 0.8
17
zeros. The second stage is selectable: a two-pole low-
pass filter (LPF) for the fastest possible response, or
SINC (multiple zero) decimation filter for relatively
quieter operation. The PID plus the LPF result in a three
pole, two zero composite filter, while the PID plus the
SINC results in a single pole, multiple zero composite
filter. The SINC filter provides zeros at intervals equal to
f
S
/(2*DEC) where DEC is the decimation ratio (i.e. ratio
of input to output sampling rate). DEC is a software-
programmable parameter, and can be programmed
such that zero placement occurs that the PWM
frequency and its harmonics. This creates more than
100 db attenuation at these frequencies providing lower
system noise levels.
The end-to-end response of the filter is defined using
only six software parameters, and can be re-
programmed during converter operation to implement
nonlinear control response for improved transient
resolution.
As described in the ADC1 section above, limit cycle
oscillation can be avoided by increasing ADC1 LSB size
to allow the DPWM LSB to fit within a single ADC1
output code (i.e. zero-error bin). However in some
applications, it may not be desirable to lower ADC1
sensitivity. For such applications, limit cycle oscillation
can be avoided by dithering the DPWM output. The
DSP Filter Engine contains a pseudo-random,
broadband noise generator - mixing this noise into the
filter output randomly moves the gate control output(s)
over a range of 1 LSB, such that the time-averaged
resolution of the DPWM is increased.
The filter response is programmed using S-domain
design tools included in the Si8250DK development kit,
greatly minimizing software writing tasks.
Pulse-by-pulse
Current
comparator with 4-bit DAC threshold generator and 2-bit
programmable leading-edge blanking delay generator.
The comparator output causes the DPWM to terminate
the on-going portions of the active outputs when the
peak current signal applied to the IPK input exceeds the
threshold setting. Hardware performs an OCP supply
shutdown when the number of consecutive current limit
events equals a programmed maximum.
DPWM: Output generator may be programmed for
pulse width (PWM) or phase-shift modulation using
design tools contained in the Si8250DK design kit. The
DPWM may be modulated by the front-end of the
Control Processor (ADC1 and DSP Filter Engine); or by
the CPU. The DPWM has individually programmable
stop states for supply off (disable) and OCP. Software
bypass mode allows the CPU to force selected outputs
high or low while the remaining outputs continue normal
Limiter/OCP:
High-speed
operation. The DPWM includes an external SYNC input
and ENABLE input, both of which can be connected to
the I/O pins. The Enable is a logic input used to turn the
power supply on and off. It can be configured to be
active high or active low. The SYNC input allows the
start of each switching cycle to be synchronized to an
external clock source, including another Si8250/1/2.
3.3. System Management Processor Func-
tional Block Descriptions
ADC0: Self-sequencing, 10-input, 200 Ksps analog-to-
digital converter. This general-purpose ADC acquires
other analog system parameters for supplemental
control by the CPU (e.g. dead time control using
average input current as the control variable). ADC0
also converts the output of the on-board temperature
sensor. Eight of the ten analog inputs may be
connected to the I/O pins for external interface. The
remaining two analog inputs (Vsense and Temp Sensor)
are internally connected. When placed in Auto
Sequencing mode, ADC0 automatically converts, stores
and limit-checks each analog input, and interrupts the
CPU when a converted result is outside of its
programmed range. This feature greatly facilitates
protection functions because all measurement and
comparison operations are automated.
Temperature Sensor: This sensor measures the die
temperature of the Si8250/1/2. It can achieve 3 C
accuracy with a single-point calibration and 1 C with a
two-point calibration. The temperature output signal is
digitized by ADC0.
8051 CPU: 50MIPS CPU core with 1K of SRAM and up
to 32 kB of Flash memory. This processor has its own
on-board oscillator and PLL, reset sources and real-
time in-system hardware debug interface eliminating the
need for external processor supervisors, timebases,
and "emulators". The CPU has an external interrupt
(INT0/) that can be connected to an external device via
the I/O pins. When interrupted, the CPU suspends
execution of the current task, and immediately vectors
to an interrupt service routine specifically designed to
handle the interrupting device.
Digital peripherals: Peripherals include: four 16-bit
timers, a three-channel programmable counter array
(PCA), each channel useful as a PWM, an SMBus port
useful as a PMBus interface, a UART (useful as a serial
data port for isolated applications, and two 8-bit I/O port
latches for logic control outputs.
相关PDF资料 |
PDF描述 |
|---|---|
| SI8250-IM | DIGITAL POWER CONTROLLER |
| SI8250-IQ | DIGITAL POWER CONTROLLER |
| SI8401DB-T1 | P-Channel 20-V (D-S) MOSFET, Low-Threshold |
| SI8401DB-T1-E3 | P-Channel 20-V (D-S) MOSFET, Low-Threshold |
| SI8401DB | Single P-Channel MOSFET; |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI8250DK | 功能描述:电源管理IC开发工具 Development kit for Si8250/1/2 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| SI8250-IM | 功能描述:电压监测器/监控器 SMPS Controller RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| SI8250-IMR | 制造商:Silicon Laboratories Inc 功能描述:VOLT SUPERVISOR PWR SUPPLY 0.05V TO 0.8V 28QFN - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC DIGITAL PWR CONTROLLER 32LQFP 制造商:Silicon Laboratories Inc 功能描述:32K 28 Pin SMPS Controller |
| SI8250-IQ | 功能描述:电压监测器/监控器 SMPS Controller RoHS:否 制造商:Texas Instruments 监测电压数:2 监测电压:Adjustable 输出类型:Open Drain 欠电压阈值: 过电压阈值: 准确性:1 % 工作电源电压:1.5 V to 6.5 V 工作电源电流:1.8 uA 最大工作温度:+ 125 C 封装 / 箱体:SON-6 安装风格:SMD/SMT |
| SI8250-IQR | 制造商:Silicon Laboratories Inc 功能描述:VOLT SUPERVISOR PWR SUPPLY 0.05V TO 0.8V 32LQFP - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC DIGITAL PWR CONTROLLER 32LQFP 制造商:Silicon Laboratories Inc 功能描述:32K 32 Pin SMPS Controller |
发布紧急采购，3分钟左右您将得到回复。