- 您现在的位置：买卖IC网 > PDF目录18842 > SI8518-C-IS (Silicon Laboratories Inc)SENSOR CURR 10A 5.5V UNI 20SOIC PDF资料下载
参数资料
| 型号： | SI8518-C-IS |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 10/36页 |
| 文件大小： | 0K |
| 描述： | SENSOR CURR 10A 5.5V UNI 20SOIC |
| 标准包装： | 38 |
| 电流 - 感应： | 10A |
| 精确度： | ±5% |
| 灵敏度： | 196mV/A |
| 电流 - 电源： | 4mA |
| 传感器类型： | 闭环 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出： | 可配置 |
| 频率： | 50kHz ~ 1MHz |
| 电极标记： | 单向 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 管件 |
| 其它名称： | 336-1734-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Si85xx
?
?
FAULT output (Si8517/8/9): Goes low when
external reset timing is in error.
Ease-of-use: Other than conventional power and
grounding techniques, no special board layout
considerations are required. Built-in timing interface
circuits allow already-available system switching
signals to be used for reset with no external circuits
required.
2.3. Integrator Reset and
Current Measurement
The Si85xx measures current flowing from the IIN to
IOUT terminals. Current is allowed to flow in the
opposite direction, but will not be measured (OUT1 and
OUT 2 remain at their minimum values during reverse
current flow. Reverse current flow will not damage the
Si85xx).
2.1. Under Voltage Lockout (UVLO)
UVLO is provided to prevent erroneous operation during
device start-up and shutdown or when VDD is
significantly below the specified operating range. The
Si85xx is in UVLO state when VDD < V UVLO (Figure 4).
During UVLO, the output(s) are held at minimum value
regardless of the amount of current flowing from IIN to
IOUT, and signals on integrator reset inputs R1–R4 are
ignored. The Si85xx exits UVLO when VDD > (V UVLO +
V HYST ).
2.2. Device Startup
Upon exit from UVLO, the Si85xx performs a voltage
offset and temperature self-calibration cycle. During this
time, output(s) are held at minimum value and reset
inputs (R1-R4) are ignored. The reset inputs are
enabled at the end of the self-calibration cycle, and an
integrator reset cycle is initiated on the first occurrence
of active signals on R1–R4. A current measurement is
initiated immediately after the completion of the
integrator reset cycle, and the resulting current
waveforms appear on the output pins. This "reset-
measure-reset" pattern repeats throughout steady-state
operation.
V UVLO + V HYST
To achieve the specified accuracy, the integrator
capacitor must be discharged (reset) for time period t R
prior to the start of every measurement cycle. This
cycle-by-cycle reset is implemented by connecting
existing system gate control signals to the R1–R4 inputs
in a way that resets the integrator when no current is
flowing from IIN to IOUT. To achieve rated accuracy, the
reset cycle must be completed prior to the start of the
measurement cycle. For maximum flexibility, integrator
reset operation can be configured in one of two ways:
Option 1: The start and duration of reset is
determined by the states of the timing
signals applied to R1–R4.
Option 2: The timing signals applied to R1–R4 trigger
the start of reset, and the duration of the
reset is determined by an onboard
programmable reset timer.
VDD
SUPPLY
First Positive Edge
Following End of Self-Cal
INTEGRATOR
DON’T CARE
tRP
tRP
RESET
Si85xx
STATUS
UNDER VOLTAGE
LOCKOUT STATE
START-UP
SELF-CAL CYCLE
RESET
MEASURE CURRENT
RESET
tCAL
tR
tR
10
Si85xx
OUTPUT
VOUT MIN
OUT1, OUT2
VALID
Figure 4. Si85xx Startup and Control Timing
Preliminary Rev. 0.4
相关PDF资料 |
PDF描述 |
|---|---|
| D3V-11G-1C23 | SWITCH SNAP 11A SPDT .187 QC |
| SI8517-C-IS | SENSOR CURR 5A 5.5V UNI 20SOIC |
| T7H8167504DN | SCR PHASE CTRL MOD 1600V 750A |
| 684-36 R/B | LEAD TEST ALLIG CLIP 36" RED/BLK |
| PT080-8-0 | CORD PATCH PIN TIP PLUG 8" BLACK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI8518-C-ISR | 制造商:Silicon Laboratories Inc 功能描述:10A CURRENT SENSOR, DUAL OUTPUT WITH FAULT OUTPUT 5KV SOIC20 - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:SENSOR CURR 10A 5.5V UNI 20SOIC 制造商:Silicon Laboratories Inc 功能描述:10A Curr Sensor Dual Output FAULT 5kV |
| Si8519-B-GM | 功能描述:板上安装电流传感器 20A Current Snsr Dual Out w/FAULT out RoHS:否 制造商:Honeywell 电流额定值:+/- 56 A 传感器/变换器类型: 电源电压:4.75 VDC to 5.25 VDC 响应时间:< 0.2 us 输出电压: 工作温度:- 40 C to + 85 C 准确性:+/- 0.24 % 频率范围: |
| Si8519-C-GM | 功能描述:板上安装电流传感器 20A Current Sensor Dual w/FAULT output RoHS:否 制造商:Honeywell 电流额定值:+/- 56 A 传感器/变换器类型: 电源电压:4.75 VDC to 5.25 VDC 响应时间:< 0.2 us 输出电压: 工作温度:- 40 C to + 85 C 准确性:+/- 0.24 % 频率范围: |
| SI8519-C-GMR | 制造商:Silicon Laboratories Inc 功能描述:20A CURRENT SENSOR, DUAL OUTPUT WITH FAULT OUTPUT - Tape and Reel |
| Si8519-C-IM | 功能描述:板上安装电流传感器 20A DUAL OUTPUT 1kV W/FAULT OUTPUT RoHS:否 制造商:Honeywell 电流额定值:+/- 56 A 传感器/变换器类型: 电源电压:4.75 VDC to 5.25 VDC 响应时间:< 0.2 us 输出电压: 工作温度:- 40 C to + 85 C 准确性:+/- 0.24 % 频率范围: |
发布紧急采购，3分钟左右您将得到回复。