- 您现在的位置：买卖IC网 > PDF目录15442 > SIP11203DLP-T1-E3 (Vishay Siliconix)IC REG CTRLR ISO PWM MLP44-16 PDF资料下载
参数资料
| 型号： | SIP11203DLP-T1-E3 |
| 厂商： | Vishay Siliconix |
| 文件页数： | 6/18页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR ISO PWM MLP44-16 |
| 标准包装： | 2,500 |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 电源电压： | 5.5 V ~ 13 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | PowerPAK? MLP44-16 |
| 包装： | 带卷 (TR) |
SiP11203, SiP11204
Vishay Siliconix
DETAILED OPERATION
SUPPLY VOLTAGE (V IN )
The SiP11203/SiP11204 are designed to operate at an
input voltage (V IN ) between 5.5 V and 13 V. The
synchronous rectifier drivers (OUTA and OUTB) are
powered directly from V IN , to facilitate setting the gate
drive voltage for the rectifier MOSFETs. Due to the
high peak currents available from the SiP11203/
SiP11204 outputs, careful attention must be paid to the
bypassing of V IN to PGND.
Internal Supply (V L )
In order to provide the internal circuitry of the
SiP11203/SiP11204 with a stable supply voltage (V L ),
the SiP11203/SiP11204 incorporate a linear pre-
regulator. Operating from V IN , the pre-regulator
provides a fixed V L of 5 V for use by the majority of the
chip. V L is regulated by V REFINT , and therefore does
not depend upon the voltage at the V REF pin. For
proper IC operation, a bypass capacitor on the order
of 1μF should be connected between V L and GND.
In normal operation, V L is intended to accommodate
the internal light load requirements, such as bias
networks and the sourcing capability of the error
REFERENCE VOLTAGE (V REF )
The SiP11203/SiP11204 incorporate an internal
voltage reference of 2.5 V. This is scaled and buffered
to drive the V REF pin at 1.225 V. The accuracy of V REF
is ± 1 % at 25 °C, with a temperature coefficient of
± 160 μV/°C, yielding a worst-case accuracy over
temperature of ± 3 % (- 40 °C to + 85 °C).
Start-up and Soft-Start Considerations
V REF is held at 0 V until V L has exceeded its UVLO R
threshold. This allows a soft-start function to be
implemented by controlling the rate of rise of voltage
on the V REF pin, which in turn causes a gradual rise in
the target voltage of the error amplifier and its
associated voltage control loop. See Figure 4, in the
Applications Information Section.
The charging rate (dV/dt) of V REF is user-settable by
choice of V REF bypass capacitor value. The I-V
characteristic of the reference output approximates
that of a constant current source, with the typical I OUT
at the V REF pin for voltages between 0 V and the final
regulated voltage of 1.225 V being 410 μA. See the
graph “V REF Start-up.”
amplifier’s output.
ERROR AMPLIFIER
Start-up Considerations
The average pre-regulator output current available to
charge the V L bypass capacitor, and the value of that
capacitor, play an important part in the start-up
sequencing of the SiP11203/SiP11204. Until V L
reaches the Chip Undervoltage Lockout threshold
(CUVLO), the part is held in a low-current standby
state. W hen V L exceeds the CUVLO voltage of 3.55 V,
the majority of the on-chip circuitry is enabled, with the
exception of the reference voltage buffer and the
output drivers (OUTA and OUTB). Finally, when the
main Undervoltage Lockout threshold (UVLO R ) is
reached, which occurs when V L reaches 90 % of its
final value, the V REF buffer and the output drivers are
enabled. This in turn allows the V REF pin to source
current, and the outputs to respond to the INA and INB
inputs. See Figure 4, in the Applications Information
Section.
The I-V characteristic of the pre-regulator approximates
that of a constant current source. W ith V IN = 7.5 V, the
typical I OUT at the V L pin for voltages between 0 V and
the final regulated voltage of 5 V is 35 mA.
www.vishay.com
6
The error amplifier is biased from the internal 5 V
supply (V L ). The input common mode range extends
down to ground and up to 3.5 V. The output stage can
source in excess of 4 mA and can sink 1 mA. The
output stage is comprised of a class-A source follower
working into a 1 mA pull down (current sink), and is
designed to drive light loads such as an optocoupler
and the series resistor. The output source current I OH
is limited by an internal 500 ? resistor, to protect the
output in the event of a short to GND. W hen sourcing
current in excess of 1 mA, the voltage drop across this
resistor should be taken into account (see graph of
V OH vs. I LOAD ). The 1 MHz amplifier has 75 degrees of
phase margin, and a large signal slew rate is (1 V/μs)
in a unitygain configuration. The input offset voltage is
typically 3 mV at 25 °C, and the offset voltage
temperature coefficient is typically 30 uV/°C. Due to its
CMOS inputs, the amplifier has low input bias and
offset currents. Both amplifier inputs as well as the
output are accessible, to facilitate meeting the
compensation requirements of specific applications.
Note that the error amplifier output is clamped low until
the V L voltage has increased past the CUVLO R
voltage level.
Document Number: 73868
S11-0975–Rev. C, 16-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B54-EY-B1 | CONVERTER MOD DC/DC 48V 50W |
| V300C8T100BL3 | CONVERTER MOD DC/DC 8V 100W |
| VI-BWK-EY-B1 | CONVERTER MOD DC/DC 40V 50W |
| VI-BWH-EY-B1 | CONVERTER MOD DC/DC 52V 50W |
| V300C8T100BL2 | CONVERTER MOD DC/DC 8V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SIP11204DLP-T1-E3 | 功能描述:开关变换器、稳压器与控制器 Sec Sync Rect Ctrl w/Overvolt Protect RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| SIP11205 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Feed-Forward Controller with Primary MOSFET Drivers for Intermediate Bus Converters |
| SIP11205DLP-T1-E3 | 功能描述:开关变换器、稳压器与控制器 Feed-Fwd Controller with MOSFET Drivers RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| SIP11205DQP-T1-E3 | 功能描述:开关变换器、稳压器与控制器 Feed-Fwd Controller with MOSFET Drivers RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| SIP11206 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Half-Bridge Controller with Primary MOSFET Drivers for Intermediate Bus Converters |
发布紧急采购，3分钟左右您将得到回复。