参数资料
| 型号： | SM3-19.44M |
| 厂商： | Connor-Winfield |
| 文件页数： | 17/36页 |
| 文件大小： | 0K |
| 描述： | IC MOD TIMING 19.440MHZ STATUM 3 |
| 标准包装： | 1 |
| 系列： | SM3 |
| 类型： | 定时模块，系统时钟 |
| PLL： | 是 |
| 主要目的： | 以太网，ADM，DSLAM，SONET/SDH，Stratum，TDM |
| 输入： | LVCMOS |
| 输出： | LVCMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 4:3 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 19.44MHz |
| 电源电压： | 3.135 V ~ 3.465 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 32-DIP 模块 |
| 包装： | 管件 |
| 其它名称： | CW642 SM3 19.44M SM319.44M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
SM3 Data Sheet #:
TM052
Page 24 of 36 Rev: 06 Date:01/26/11
Copyright 2011 The Connor-Winfield Corp. All Rights Reserved
Specifications subject to change without notice
II. To lock the unit to a reference in autonomous (automatic) mode after power up or reset, the following steps should be taken.
You can also switch from Manual to Autonomous mode directly. When doing so, please ensure that the appropriate references are
available by checking REF_AVAILABLE register (address: 0x0c).
1.
Clear bit1 of CTL_MODE register (address: 0x04). This puts the module in autonomous mode.
2.
Apply signal to the reference inputs
3.
Set the appropriate pull in range by writing to address 0x06
4.
The default bandwidth of 0.098 Hz is appropriate for Stratum 3 operation.
5.
Enable Reference mask for appropriate references by writing a 1 to the reference bit in address 0x0b.
6.
Set priority and revertivity for the input references by writing to the appropriate Ref_Frq_Priority registers (bits 3-0).
7.
Enable all Interrupts by writing 11111111 to address 0x13.
8.
Set the unit to operate in autonomous mode by clearing bit1 of address 0x04
III. Slave Mode Operation:
1.
As a Slave, the module operates in Autonomous mode.
2.
The Bandwidth is set, by default, to 1.6Hz (Bandwidth_PBO register (Address 0x03): 00001011).
3.
Note that bit 4 of the OP_MODE register (Address 0x05) is cleared.
4.
The values in Bits 3-0 of this register have no effect on the operation of the Slave module.
5.
For the Slave module to track the Master accurately, an appropriate Phase Offset value should be written to
PHASE_OFFSET register (Address 0x0e), to compensate for the path delay.
6.
The module will lock to the Cross Reference Input (XREF) from the master.
IV RESET Parameters:
1.
The reset pin should be held low for a minimum of 10 milliseconds to ensure a complete reset occurs.
2.
The SPI interface should not be accessed for a minimum of 1200ms after the reset pin is de-asserted.
Switching Master/Slave designations:
The following steps need to be taken before making Master module a Slave and vice versa.
1.
Copy the value in the PHASE_OFFSET register (Address 0x0e) of the Slave to the Master module’s PHASE_OFFSET
regsiter (Address 0x0e).
2.
Read the contents of Bits 3-0 of the Master’s OP_MODE register (Address 0x05) and copy it into Bits 3-0 of the Slave’s
OP_MODE register (Address 0x05).
3.
It is recommended that the contents of REF(1-4)_FRQ_PRIORITY registers (Address 0x1c-0x1f) and REF_MASK register
(Address 0x0b) from Master be copied to Slave to ensure seamless Master/Slave switches.
Master/Slave switches should be performed with minimal delay between switching the states of each of the two devices.
SM3 Initialization continued
相关PDF资料 |
PDF描述 |
|---|---|
| SM3E-19.44M | IC MOD TIMING 19.440MHZ STRAT 3E |
| SM802104UMG TR | IC SYNTHESIZER 2CH 24-QFN |
| SM802105UMG TR | IC SYNTHESIZER 2CH 24-QFN |
| SM802108UMG | IC SYNTEHSIZER 156.25MHZ 24QFN |
| SM802109UMG TR | IC SYNTHESIZER QUAD 100MHZ 24QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SM-31A100Kohm | 制造商:Nidec Copal 功能描述:Potentiometer, cermet trimmer, multi-turn, 0.125W, 100Kohm |
| SM-31A100ohm | 制造商:Nidec Copal 功能描述:Potentiometer, cermet trimmer, multi-turn, 0.125W, 100ohm |
| SM31A101 | 功能描述:TRIMMER 100 OHM 0.125W SMD RoHS:是 类别:电位计，可变电阻器 >> 微調器 系列:SM31 标准包装:500 系列:Trimpot® TC86 - 开放框架 电阻（欧姆）:100k 功率（瓦特）:0.3W 容差:±20% 温度系数:±250ppm/°C 匝数:单路 调节型:顶部调节 电阻材料:金属陶瓷 安装类型:通孔 端接类型:PC 引脚 包装:散装 尺寸/尺寸:方形 - 0.303" L x 0.268" W x 0.299" H（7.70mm x 6.80mm x 7.60mm） 其它名称:TC86P-104 |
| SM-31A101 | 制造商:Nidec Copal 功能描述:RES TRMR 100 OHM 20% 1/8W 5TURN 1.3MM J-HOOK SMD - Tape and Reel |
| SM31A102 | 功能描述:TRIMMER 1K OHM 0.125W SMD RoHS:是 类别:电位计，可变电阻器 >> 微調器 系列:SM31 标准包装:500 系列:Trimpot® TC86 - 开放框架 电阻（欧姆）:100k 功率（瓦特）:0.3W 容差:±20% 温度系数:±250ppm/°C 匝数:单路 调节型:顶部调节 电阻材料:金属陶瓷 安装类型:通孔 端接类型:PC 引脚 包装:散装 尺寸/尺寸:方形 - 0.303" L x 0.268" W x 0.299" H（7.70mm x 6.80mm x 7.60mm） 其它名称:TC86P-104 |
发布紧急采购，3分钟左右您将得到回复。