- 您现在的位置：买卖IC网 > PDF目录373461 > SN74LVTH18640 (Texas Instruments, Inc.) 3.3-V ABT Scan Test Device With 18-Bit Inverting Bus Transceivers(3.3V ABT 扫描检测装置(18位反相总线收发器)) PDF资料下载
参数资料
| 型号： | SN74LVTH18640 |
| 厂商： | Texas Instruments, Inc. |
| 英文描述： | 3.3-V ABT Scan Test Device With 18-Bit Inverting Bus Transceivers(3.3V ABT 扫描检测装置(18位反相总线收发器)) |
| 中文描述： | 的3.3V ABT生根粉扫描测试设备与18位反相总线收发器（3.3V的ABT生根粉扫描检测装置（18位反相总线收发器）） |
| 文件页数： | 6/34页 |
| 文件大小： | 707K |
| 代理商： | SN74LVTH18640 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
SN54LVTH18640, SN54LVTH182640, SN74LVTH18640, SN74LVTH182640
3.3-V ABT SCAN TEST DEVICES
WITH 18-BIT INVERTING BUS TRANSCEIVERS
SCBS310C – MARCH 1994 – REVISED DECEMBER 1996
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
state diagram description
The TAP controller is a synchronous finite state machine that provides test control signals throughout the device.
The state diagram shown in Figure 1 is in accordance with IEEE Standard 1149.1-1990. The TAP controller
proceeds through its states based on the level of TMS at the rising edge of TCK.
As shown, the TAP controller consists of 16 states. There are six stable states (indicated by a looping arrow in
the state diagram) and ten unstable states. A stable state is a state the TAP controller can retain for consecutive
TCK cycles. Any state that does not meet this criterion is an unstable state.
There are two main paths through the state diagram: one to access and control the selected data register and
one to access and control the instruction register. Only one register can be accessed at a time.
Test-Logic-Reset
The device powers up in the Test-Logic-Reset state. In the stable Test-Logic-Reset state, the test logic is reset
and is disabled so that the normal logic function of the device is performed. The instruction register is reset to
an opcode that selects the optional IDCODE instruction, if supported, or the BYPASS instruction. Certain data
registers also can be reset to their power-up values.
The state machine is constructed such that the TAP controller returns to the Test-Logic-Reset state in no more
than five TCK cycles if TMS is left high. The TMS pin has an internal pullup resistor that forces it high if left
unconnected or if a board defect causes it to be open circuited.
For the ’LVTH18640 and ’LVTH182640, the instruction register is reset to the binary value 10000001, which
selects the IDCODE instruction. Bits 43–40 in the boundary-scan register are reset to logic 0, ensuring that
these cells, which control A-port and B-port outputs, are set to benign values (i.e., if test mode were invoked,
the outputs would be at high-impedance state). Reset values of other bits in the boundary-scan register should
be considered indeterminate. The boundary-control register is reset to the binary value 010, which selects the
PSA test operation.
Run-Test/Idle
The TAP controller must pass through the Run-Test/Idle state (from Test-Logic-Reset) before executing any test
operations. The Run-Test/Idle state also can be entered following data-register or instruction-register scans.
Run-Test/Idle is a stable state in which the test logic can be actively running a test or can be idle. The test
operations selected by the boundary-control register are performed while the TAP controller is in the
Run-Test/Idle state.
Select-DR-Scan, Select-lR-Scan
No specific function is performed in the Select-DR-Scan and Select-lR-Scan states, and the TAP controller exits
either of these states on the next TCK cycle. These states allow the selection of either data-register scan or
instruction-register scan.
Capture-DR
When a data-register scan is selected, the TAP controller must pass through the Capture-DR state. In the
Capture-DR state, the selected data register can capture a data value as specified by the current instruction.
Such capture operations occur on the rising edge of TCK, upon which the TAP controller exits the
Capture-DR state.
P
相关PDF资料 |
PDF描述 |
|---|---|
| SN54LVTH18646A | 3.3-V ABT Scan Test Device With 18-Bit Transceivers and Registers(3.3V ABT 扫描检测装置(18位收发器和寄存器)) |
| SN54LVTH182646A | 3.3-V ABT Scan Test Device With 18-Bit Transceivers and Registers(3.3V ABT 扫描检测装置(18位收发器和寄存器)) |
| SN54LVTH18652A | 3.3-V ABT Scan Test Device With 18-Bit Transceivers and Registers(3.3V ABT 扫描检测装置(18位收发器和寄存器)) |
| SN54LVTH182652A | 3.3-V ABT Scan Test Device With 18-Bit Transceivers and Registers(3.3V ABT 扫描检测装置(18位收发器和寄存器)) |
| SN54LVTH2245 | Octal 3-State Noninverting Buffer/Line Driver/Line Receiver; Package: 20 LEAD PDIP; No of Pins: 20; Container: Rail; Qty per Container: 18 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SN74LVTH18646APM | 功能描述:特定功能逻辑 3.3-V ABT w/18-Bit Trnscvr & Register RoHS:否 制造商:Texas Instruments 产品: 系列:SN74ABTH18502A 工作电源电压:5 V 封装 / 箱体:LQFP-64 封装:Tube |
| SN74LVTH18646APMG4 | 功能描述:特定功能逻辑 3.3-V ABT w/18-Bit Trnscvr & Register RoHS:否 制造商:Texas Instruments 产品: 系列:SN74ABTH18502A 工作电源电压:5 V 封装 / 箱体:LQFP-64 封装:Tube |
| SN74LVTH18652APM | 功能描述:特定功能逻辑 3.3-V ABT w/18-Bit Trnscvr & Register RoHS:否 制造商:Texas Instruments 产品: 系列:SN74ABTH18502A 工作电源电压:5 V 封装 / 箱体:LQFP-64 封装:Tube |
| SN74LVTH18652APMG4 | 功能描述:特定功能逻辑 3.3-V ABT w/18-Bit Trnscvr & Register RoHS:否 制造商:Texas Instruments 产品: 系列:SN74ABTH18502A 工作电源电压:5 V 封装 / 箱体:LQFP-64 封装:Tube |
| SN74LVTH2245DBR | 功能描述:总线收发器 Tri-St ABT Octal Bus RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。