- 您现在的位置：买卖IC网 > PDF目录382545 > SPT7936SCT (FAIRCHILD SEMICONDUCTOR CORP) 12-BIT, 28 MSPS SAMPLING A/D CONVERTER PDF资料下载
参数资料
| 型号： | SPT7936SCT |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | ADC |
| 英文描述： | 12-BIT, 28 MSPS SAMPLING A/D CONVERTER |
| 中文描述： | 1-CH 12-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP44 |
| 封装： | TQFP-44 |
| 文件页数： | 6/8页 |
| 文件大小： | 59K |
| 代理商： | SPT7936SCT |
6
8/1/00
SPT7936
ANALOG INPUT
The SPT7936 has a differential input that should have a
common mode voltage of +1.5 V. The input voltage range is
determined by the reference voltages which may be gener-
ated internally or applied externally.
The input of the SPT7936 can be configured in various ways
depending on if a single-ended or differential, AC- or DC-
coupled input is desired.
The AC coupled input is most conveniently implemented
using a transformer with a center tapped secondary winding.
The center tap is connected to the V
CM
pin as shown in
figure 2. To obtain low distortion, it is important that the
selected transformer does not exhibit core saturation at the
full-scale voltage. Excellent results are obtained with the Mini
Circuits T1-6T or T1-1T. Proper termination of the input is
important for input signal purity. A small capacitor across the
inputs attenuates kickback noise from the internal sample
and hold.
Figure 3 illustrates a solution (based on operational amplifi-
ers) that can be used if a a DC coupled single-ended input is
desired. The selection criteria of the buffer op-amps is as
follows:
- Open loop gain >75 dB
- Gain bandwidth product >50 MHz
- Total harmonic distortion
≤
-75 dB
- Signal to Noise ratio >75 dB
REFERENCES
The SPT7936 can use either an internal or external voltage
reference. When the digital input EXTREF is high, the exter-
nal reference is used. When EXTREF is low, the internal
reference is used.
INTERNAL REFERENCE
The internal references are set at +1.0 V and +2.0 V. When
the internal reference is used, the full-scale range of the
analog input is set at
±
1.0 V differential. Do not connect
external references when the internal reference is used.
EXTERNAL REFERENCE
When external references are used, the voltages applied to
the V
REF
+ and V
REF
- pins determine the input voltage range
which is equal to
±
(V
REF
+ - V
REF
-). Externally generated
reference voltages must be connected to these pins and
should be symmetric about the common mode voltage. (See
figure 2, Typical Interface Circuit.)
COMMON MODE OUTPUT VOLTAGE
REFERENCE CIRCUIT
The SPT7936 has an on-board common mode voltage refer-
ence circuit (V
CM
). It is set at +1.5 V and can drive loads of up
to 20
μ
A. This circuit is commonly used to drive the center tap
of the RF transformer in fully differential applications. For
single-ended applications, this output can be used to provide
the level shifting required for the single-to-differential con-
verter conversion circuit.
BIAS CIRCUITS
The best AC performance is achieved when the bias currents
are optimized for the selected sample rate. Two digital input
pins are provided to control the optimum internal bias cur-
rents. Table I shows the settings for Bias 0 and Bias 1 at
selected frequencies.
Table I - Frequencies for Biases 0 and 1
Typical Power
Dissipation
Ext. Ref.
25 mW
61 mW
172 mW
248 mW
Bias 1 Bias 0 Description
0
0
0
1
1
0
1
1
Int. Ref.
36 mW
73 mW
184 mW
260 mW
Sleep mode (power save)*
≤
5 MHz sampling
≤
20 MHz sampling
≤
28 MHz sampling
*Clock = 28 MHz
Figure 3 - DC-Coupled Single-Ended-to-Differential
Conversion (Power Supplies are Not
Shown)
VCM
R3
(R3)/2
+
_
Input
Voltage
(
±
0.5 V)
R3
R
R2
R2
+
_
+
_
R
R
R
51
51
R
ADC
VIN+
VIN–
15 pF
51
POWER SUPPLIES AND GROUNDING
The SPT7936 is operated from a single power supply in the
range of 3.0 to 3.6 volts. Nominal operation is suggested to
be 3.3 volts. All power supply pins should be bypassed as
close to the package as possible. The analog and digital
grounds should be connected together with a ferrite bead as
shown in the typical interface circuit and as close to the ADC
as possible.
相关PDF资料 |
PDF描述 |
|---|---|
| SPT8100SIT | 16-BIT, 5 MSPS CMOS A/D CONVERTER |
| SPT8100 | 16-BIT, 5 MSPS CMOS A/D CONVERTER |
| SPT9689AIC | DUAL ULTRAFAST VOLTAGE COMPARATOR |
| SPT9689 | DUAL ULTRAFAST VOLTAGE COMPARATOR |
| SPT9689ACU | DUAL ULTRAFAST VOLTAGE COMPARATOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SPT7937 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:12-BIT, 28 MSPS, 170 mW A/D CONVERTER |
| SPT7937SIR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:12-BIT, 28 MSPS, 170 mW A/D CONVERTER |
| SPT7938 | 制造商:CADEKA 制造商全称:CADEKA 功能描述:12-BIT, 40 MSPS, 170 mW A/D CONVERTER |
| SPT7938SIR | 制造商:CADEKA 制造商全称:CADEKA 功能描述:12-BIT, 40 MSPS, 170 mW A/D CONVERTER |
| SPT-8 | 制造商:Portasol 功能描述:4.8mm DF Tip for 21-14190 and 21-14192 |
发布紧急采购，3分钟左右您将得到回复。