- 您现在的位置：买卖IC网 > PDF目录2110 > SSM2319CBZ-R2 (Analog Devices Inc)IC AMP AUDIO 3.7W MONO D 9WLCSP PDF资料下载
参数资料
| 型号： | SSM2319CBZ-R2 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC AMP AUDIO 3.7W MONO D 9WLCSP |
| 标准包装： | 1 |
| 类型： | D 类 |
| 输出类型： | 1-通道（单声道） |
| 在某负载时最大输出功率 x 通道数量： | 3.7W x 1 @ 3 欧姆 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 特点： | 消除爆音，差分输入，短路和热保护，关闭 |
| 安装类型： | 表面贴装 |
| 供应商设备封装： | 9-WLCSP（1.52 x 1.69） |
| 封装/外壳： | 9-UFBGA，WLCSP |
| 包装： | 标准包装 |
| 其它名称： | SSM2319CBZ-R2DKR |
SSM2319
Rev. 0 | Page 14 of 20
THEORY OF OPERATION
OVERVIEW
OUTPUT MODULATION DESCRIPTION
The SSM2319 mono Class-D audio amplifier features a filterless
modulation scheme that greatly reduces the external components
count, conserving board space and, thus, reducing systems cost.
The SSM2319 does not require an output filter. Instead, it relies
on the inherent inductance of the speaker coil and the natural
filtering of the speaker and human ear to fully recover the audio
component of the square wave output. Most Class-D amplifiers
use some variation of pulse-width modulation (PWM), but the
SSM2319 uses a Σ-Δ modulation to determine the switching
pattern of the output devices, resulting in a number of important
benefits. Σ-Δ modulators do not produce a sharp peak with many
harmonics in the AM frequency band, as pulse-width modulators
often do. Σ-Δ modulation reduces the amplitude of spectral
components at high frequencies, reducing EMI emission that
may otherwise be radiated by speakers and long cable traces.
Due to the inherent spread-spectrum nature of Σ-Δ
modulation, the need for oscillator synchronization is eliminated
for designs incorporating multiple SSM2319 amplifiers.
The SSM2319 uses 3-level Σ-Δ output modulation. Each output
is able to swing from GND to VDD and vice versa. Ideally, when
no input signal is present, the output differential voltage is 0 V
because there is no need to generate a pulse. In a real-world
situation, there are always noise sources present. Due to the
constant presence of noise, a differential pulse is generated
in response to this stimulus. A small amount of current flows
into the inductive load when the differential pulse is generated.
However, most of the time, the output differential voltage is 0 V,
due to the Analog Devices, Inc., patented 3-level, Σ-Δ output
modulation feature. This feature ensures that the current flowing
through the inductive load is small.
When the user wants to send an input signal, an output pulse is
generated to follow the input voltage. The differential pulse density
is increased by raising the input signal level. Figure 36 depicts
3-level Σ-Δ output modulation with and without input stimulus.
OUTPUT > 0V
+5V
0V
OUT+
+5V
0V
OUT–
+5V
0V
VOUT
OUTPUT < 0V
+5V
0V
OUT+
+5V
0V
OUT–
0V
–5V
VOUT
OUTPUT = 0V
OUT+
+5V
0V
+5V
0V
OUT–
+5V
–5V
0V
VOUT
07
55
0-
0
34
The SSM2319 also offers protection circuits for overcurrent and
temperature protection.
GAIN
The SSM2319 has a default gain of 12 dB that can be reduced by
using a pair of external resistors with a value calculated as follows:
External Gain Settings = 160 kΩ/(40 kΩ + REXT)
POP-AND-CLICK SUPPRESSION
Voltage transients at the output of the audio amplifiers can occur
when shutdown is activated or deactivated. Voltage transients as
low as 10 mV can be heard as an audio pop in the speaker. Clicks
and pops can also be classified as undesirable audible transients
generated by the amplifier system and, therefore, as not coming
from the system input signal. Such transients can be generated
when the amplifier system changes its operating mode. For
example, audible transient sources include system power-up/
power-down, mute/unmute, an input source change, and a sample
rate change. The SSM2319 has a pop-and-click suppression
architecture that reduces these output transients, resulting in
noiseless activation and deactivation.
Figure 36. 3-Level Σ-Δ Output Modulation With and Without Input Stimulus
相关PDF资料 |
PDF描述 |
|---|---|
| SSM2335CBZ-R2 | IC AMP AUDIO 4.28W MONO D 9WLCSP |
| SSM2356CBZ-RL | IC AMP AUD 2X2W STER D 16WLCSP |
| SSM2375CBZ-REEL7 | IC AMP AUDIO 4.28W MONO D 9WLCSP |
| SSM2377ACBZ-RL | IC AUDIO AMP 2.5W MONO D 9WLCSP |
| SSM2380CBZ-REEL7 | IC AMP AUD 2X2W STER D 16WLCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SSM2319CBZ-REEL | 功能描述:IC AMP AUDIO 3.7W MONO D 9WLCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:D 类 输出类型:1-通道（单声道），带立体声耳机 在某负载时最大输出功率 x 通道数量:930mW x 1 @ 8 欧姆; 40mW x 2 @ 16 欧姆 电源电压:2.7 V ~ 5.5 V 特点:消除爆音，差分输入，I²C，静音，关闭，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) 其它名称:MAX97000EWA+T-ND |
| SSM2319CBZ-REEL7 | 功能描述:IC AMP AUDIO 3W MONO D 9WLCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 标准包装:2,000 系列:- 类型:AB 类 输出类型:2 通道（立体声） 在某负载时最大输出功率 x 通道数量:- 电源电压:4 V ~ 18 V 特点:- 安装类型:通孔 供应商设备封装:8-DIP 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 |
| SSM2335 | 制造商:AD 制造商全称:Analog Devices 功能描述:Filterless, High Efficiency, Mono 3 W Class-D Audio Amplifier |
| SSM2335CBZ-R2 | 功能描述:IC AMP AUDIO 4.28W MONO D 9WLCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| SSM2335CBZ-REEL | 功能描述:IC AMP AUDIO 4.28W MONO D 9WLCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:- 标准包装:2,000 系列:- 类型:AB 类 输出类型:2 通道（立体声） 在某负载时最大输出功率 x 通道数量:- 电源电压:4 V ~ 18 V 特点:- 安装类型:通孔 供应商设备封装:8-DIP 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。