- 您现在的位置：买卖IC网 > PDF目录10940 > SSM2603CPZ-REEL (Analog Devices Inc)IC CODEC AUDIO LOW POWER 28LFCSP PDF资料下载
参数资料
| 型号： | SSM2603CPZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/32页 |
| 文件大小： | 0K |
| 描述： | IC CODEC AUDIO LOW POWER 28LFCSP |
| 标准包装： | 5,000 |
| 类型： | 立体声音频 |
| 分辨率（位）： | 24 b |
| ADC / DAC 数量： | 2 / 2 |
| 三角积分调变： | 无 |
| S/N 比，标准 ADC / DAC (db)： | 90 / 100 |
| 电压 - 电源，模拟： | 1.8 V ~ 3.6 V |
| 电压 - 电源，数字： | 1.5 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 28-LFCSP-VQ |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Data Sheet
SSM2603
Rev. C | Page 13 of 32
ANALOG INTERFACE
Signal Chain
The SSM2603 includes stereo single-ended line and monaural
microphone inputs to the on-board ADC. Either the line inputs
or the microphone input, but not both simultaneously, can be
connected to the ADC by setting the INSEL bit (Register R4,
Bit D2). In addition, the line or microphone inputs can be routed
and mixed directly to the output terminals via the SIDETONE_EN
(Register R4, Bit D5) and BYPASS (Register R4, Bit D3) bits.
The SSM2603 also includes line and headphone outputs from
the on-board DAC.
Stereo Line and Monaural Microphone Inputs
The SSM2603 contains a set of single-ended stereo line inputs
(RLINEIN and LLINEIN) that are internally biased to VMID
by a voltage divider placed between AVDD and AGND. The
line input signal can be connected to the internal ADC and, if
desired, routed directly to the outputs via the bypass path by
using the bypass bit (Register R4, Bit D3).
Figure 19. Line Input to ADC
The line input volume can be adjusted from 34.5 dB to +33 dB
in steps of +1.5 dB by setting the LINVOL (Register R0, Bit D0 to
Bit D5) and RINVOL (Register R1, Bit D0 to Bit D5) bits. Volume
control, by default, is independently adjustable on both right and
left line inputs. However, the LRINBOTH or RLINBOTH bit, if
selected, simultaneously loads both sets of volume control with
the same value. The user can also set the LINMUTE (Register R0,
Bit D7) and RINMUTE (Register R1, Bit D7) bits to mute the line
input signal to the ADC.
The high impedance, low capacitance monaural microphone
input pin (MICIN) has two gain stages and a microphone bias
level (MICBIAS) that is internally biased to the VMID voltage
level by a voltage divider placed between AVDD and AGND.
The microphone input signal can be connected to the internal
ADC and, if desired, routed directly to the outputs via the sidetone
path by using the SIDETONE_EN bit (Register R4, Bit D5).
Figure 20. Microphone Input to ADC
The first gain stage is composed of a low noise operational
amplifier set to an inverting configuration with integrated
50 k feedback and 10 k input resistors. The default
microphone input signal gain is 14 dB. An external resistor
(REXT) can be connected in series with the MICIN pin to reduce
the first-stage gain of the microphone input signal to as low as
0 dB by using the following equation:
Microphone Input Gain = 50 k/(10 k + REXT)
The second-stage gain of the microphone signal path is derived
from the internal microphone boost circuitry. The available
settings are 0 dB and 20 dB and are controlled by the MICBOOST
(Register R4, Bit D0) bit. To achieve 20 dB of secondary gain
boost, the user can select MICBOOST
In similar functionality to the line inputs, the MUTEMIC bit
(Register R4, Bit D1) can be set to mute the microphone input
signal to the ADC.
Note that when sourcing audio data from both line and
microphone inputs, the maximum full-scale input of the ADC
is 1.0 V rms when AVDD = 3.3 V. Do not source any input
voltage larger than full scale to avoid overloading the ADC,
which causes distortion of sound and deterioration of audio
quality. For best sound quality in both microphone and line
inputs, gain should be carefully configured so that the ADC
receives a signal equal to its full scale. This maximizes the
signal-to-noise ratio for best total audio quality.
07241-
031
ADC
OR
BYPASS
LINEIN
AVDD
VMID
AGND
+
–
07241-
032
ADC
OR
SIDETONE
INTERNAL CIRCUITRY
MICIN
AVDD
VMID
AGND
REXT
GAIN =
50k
(REXT + 10k)
10k
50k
0dB/20dB
GAIN BOOST
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B21-IW-B1 | CONVERTER MOD DC/DC 12V 100W |
| CS42L55-CNZR | IC CODEC STER H-HDPN AMP 36-QFN |
| DSP56F807VF80 | IC DSP 80MHZ 60K FLASH 160-BGA |
| VI-B20-IW-B1 | CONVERTER MOD DC/DC 5V 100W |
| MC9328MXLCVM15 | IC MCU I.MXL 150MHZ 256-MAPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SSM2603CPZ-REEL7 | 功能描述:IC CODEC AUDIO LOW POWER 28LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 编解码器 系列:- 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率（位）:18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比，标准 ADC / DAC (db):81.5 / 88 动态范围，标准 ADC / DAC (db):82 / 87.5 电压 - 电源，模拟:2.6 V ~ 3.3 V 电压 - 电源，数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP（7x7） 包装:带卷 (TR) |
| SSM2603-EVALZ | 功能描述:BOARD EVALUATION FOR SSM2603 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| SSM2603GY | 制造商:SSC 制造商全称:Silicon Standard Corp. 功能描述:P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
| SSM2604 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power Audio Codec |
| SSM2604CPZ-R2 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。