- 您现在的位置：买卖IC网 > PDF目录384931 > ST16C2550CJ44 (STARTECH SEMICONDUCTOR INC) DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S PDF资料下载
参数资料
| 型号： | ST16C2550CJ44 |
| 厂商： | STARTECH SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S |
| 中文描述： | 2 CHANNEL(S), 448K bps, SERIAL COMM CONTROLLER, PQCC44 |
| 文件页数： | 17/34页 |
| 文件大小： | 443K |
| 代理商： | ST16C2550CJ44 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
ST16C2550
17
Rev. 3.20
FCR BIT-3:
Logic 0 = Set DMA mode 0. (normal default condi-
tion)
Logic 1 = Set DMA mode 1.
Transmit operation in mode 0:
When the 2550 is in the ST16C450 mode (FIFOs
disabled, FCR bit-0 = logic 0) or in the FIFO mode
(FIFOs enabled, FCR bit-0 = logic 1, FCR bit-3 = logic
0) and when there are no characters in the transmit
FIFO or transmit holding register, the -TXRDY pin in
44/48 pin packages will be a logic 0. Once active the
-TXRDY pin will go to a logic 1 after the first character
is loaded into the transmit holding register.
Receive operation in mode 0:
When the 2550 is in mode 0 (FCR bit-0 = logic 0) or
in the FIFO mode (FCR bit-0 = logic 1, FCR bit-3 =
logic 0) and there is at least one character in the
receive FIFO, the -RXRDY pin will be a logic 0. Once
active the -RXRDY pin on 44/48 pin packages will go
to a logic 1 when there are no more characters in the
receiver.
Transmit operation in mode 1:
When the 2550 is in FIFO mode ( FCR bit-0 = logic 1,
FCR bit-3 = logic 1 ), the -TXRDY pin on 44/48 pin
packages will be a logic 1 when the transmit FIFO is
completely full. It will be a logic 0 if one or more FIFO
locations are empty.
Receive operation in mode 1:
When the 2550 is in FIFO mode (FCR bit-0 = logic 1,
FCR bit-3 = logic 1) and the trigger level has been
reached, or a Receive Time Out has occurred, the -
RXRDY pin on 44/48 pin packages will go to a logic 0.
Once activated, it will go to a logic 1 after there are no
more characters in the FIFO.
FCR BIT 4-5:
Not Used - initialized to a logic 0.
FCR BIT 6-7: (logic 0 or cleared is the default condi-
tion, RX trigger level = 1)
These bits are used to set the trigger level for the
receive FIFO interrupt.
An interrupt is generated when the number of charac-
ters in the FIFO equals the programmed trigger level.
However the FIFO will continue to be loaded until it is
full.
BIT-7
BIT-6
RX FIFO trigger level
0
0
1
1
0
1
0
1
01
04
08
14
Interrupt Status Register (ISR)
The 2550 provides four levels of prioritized interrupts
to minimize external software interaction. The Inter-
rupt Status Register (ISR) provides the user with four
interrupt status bits. Performing a read cycle on the
ISR will provide the user with the highest pending
interrupt level to be serviced. No other interrupts are
acknowledged until the pending interrupt is serviced.
Whenever the interrupt status register is read, the
interrupt status is cleared. However it should be noted
that only the current pending interrupt is cleared by the
read. A lower level interrupt may be seen after reread-
ing the interrupt status bits. The Interrupt Source
Table 6 (below) shows the data values (bits 0-3) for the
four prioritized interrupt levels and the interrupt
sources associated with each of these interrupt levels:
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C2550CP40 | Power Supply IC; Supply Voltage Max:6V; Output Voltage:1.3V; Package/Case:20-TSSOP; Leaded Process Compatible:No; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Supply Voltage Min:2.7V; Mounting Type:Surface Mount |
| ST16C2550IQ48 | DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S |
| ST16C2550 | Dual UART with 16-Byte of Transmit and Receive FIFO(双通用异步接收器/发送器（带16字节接收和发送先进先出）) |
| ST16C2552 | Dual UART with 16-Byte Transmit and Receive FIFO(双通用异步接收器/发送器（带16字节接收和发送先进先出）) |
| ST16C450 | UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C2550CJ44-F | 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CJ44TR-F | 功能描述:UART 接口集成电路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CP40 | 功能描述:UART 接口集成电路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CP40-F | 功能描述:UART 接口集成电路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CQ-0A-EB | 功能描述:界面开发工具 EVAL SYSTEM RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。