- 您现在的位置：买卖IC网 > PDF目录384931 > ST16C2550CJ44 (STARTECH SEMICONDUCTOR INC) DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S PDF资料下载
参数资料
| 型号： | ST16C2550CJ44 |
| 厂商： | STARTECH SEMICONDUCTOR INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S |
| 中文描述： | 2 CHANNEL(S), 448K bps, SERIAL COMM CONTROLLER, PQCC44 |
| 文件页数： | 9/34页 |
| 文件大小： | 443K |
| 代理商： | ST16C2550CJ44 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
ST16C2550
9
Rev. 3.20
Table 3, INTERNAL REGISTER DECODE
A2
A1
A0
READ MODE
WRITE MODE
General Register Set (THR/RHR, IER/ISR, MCR/MSR, LCR/LSR, SPR): Note 1*
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Receive Holding Register
Transmit Holding Register
Interrupt Enable Register
FIFO Control Register
Line Control Register
Modem Control Register
Interrupt Status Register
Line Status Register
Modem Status Register
Scratchpad Register
Scratchpad Register
Baud Rate Register Set (DLL/DLM): Note *2
0
0
0
0
0
1
LSB of Divisor Latch
MSB of Divisor Latch
LSB of Divisor Latch
MSB of Divisor Latch
Note 1* The General Register set is accessible only when CS A/B is a logic 0.
Note 2* The Baud Rate register set is accessible only when CS A/B is a logic 0 and LCR bit-7 is a logic 1.
FIFO Operation
The 16 byte transmit and receive data FIFOs are
enabled by the FIFO Control Register (FCR) bit-0. The
user can set the receive trigger level via FCR bits 6-
7 but not the transmit trigger level. The transmit
interrupt trigger level is set to 16 following a reset. The
receiver FIFO section includes a time-out function to
ensure data is delivered to the external CPU. An
interrupt is generated whenever the Receive Holding
Register (RHR) has not been read following the load-
ing of a character or the receive trigger level has not
been reached.
Hardware/Software and Time-out Interrupts
The interrupts are enabled by IER bits 0-3. Care must
be taken when handling these interrupts. Following a
reset the transmitter interrupt is enabled, the 2550 will
issue an interrupt to indicate that transmit holding
register is empty. This interrupt must be serviced prior
to continuing operations. The LSR register provides
the current singular highest priority interrupt only. It
could be noted that CTS and RTS interrupts have
lowest interrupt priority. A condition can exist where a
higher priority interrupt may mask the lower priority
CTS/RTS interrupt(s). Only after servicing the higher
pending interrupt will the lower priority CTS/ RTS
interrupt(s) be reflected in the status register. Servic-
ing the interrupt without investigating further interrupt
conditions can result in data errors.
When two interrupt conditions have the same priority,
it is important to service these interrupts correctly.
Receive Data Ready and Receive Time Out have the
same interrupt priority (when enabled by IER bit-3).
The receiver issues an interrupt after the number of
characters have reached the programmed trigger
level. In this case the 2550 FIFO may hold more
characters than the programmed trigger level. Follow-
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C2550CP40 | Power Supply IC; Supply Voltage Max:6V; Output Voltage:1.3V; Package/Case:20-TSSOP; Leaded Process Compatible:No; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Supply Voltage Min:2.7V; Mounting Type:Surface Mount |
| ST16C2550IQ48 | DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S |
| ST16C2550 | Dual UART with 16-Byte of Transmit and Receive FIFO(双通用异步接收器/发送器（带16字节接收和发送先进先出）) |
| ST16C2552 | Dual UART with 16-Byte Transmit and Receive FIFO(双通用异步接收器/发送器（带16字节接收和发送先进先出）) |
| ST16C450 | UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C2550CJ44-F | 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CJ44TR-F | 功能描述:UART 接口集成电路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CP40 | 功能描述:UART 接口集成电路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CP40-F | 功能描述:UART 接口集成电路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CQ-0A-EB | 功能描述:界面开发工具 EVAL SYSTEM RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。