- 您现在的位置：买卖IC网 > PDF目录299932 > ST16C2552CJ44 (EXAR CORP) 2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44 PDF资料下载
参数资料
| 型号： | ST16C2552CJ44 |
| 厂商： | EXAR CORP |
| 元件分类： | Serial IO/Communication Controller |
| 英文描述： | 2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 封装： | PLASTIC, LCC-44 |
| 文件页数： | 3/38页 |
| 文件大小： | 447K |
| 代理商： | ST16C2552CJ44 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
ST16C2552
9
REV. 4.2.1
2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO
2.7
INTA and INTB Ouputs
The INTA and INTB interrupt outputs change according to the operating mode and enahnced features setup.
Tables 3 and 4 summarize the operating behavior for the transmitter and receiver. Also see Figures 16
through 21.
2.8
Crystal Oscillator or Ext. Clock Input
The 2552 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. SEE”PROGRAMMABLE BAUD
FIGURE 4. TYPICAL OSCILLATOR CONNECTIONS
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 2), with an external 500k
to
1 M
resistor across it. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal
baud rate generator for standard or custom rates. Typical oscillator connections are shown in Figure 4. For
further reading on oscillator circuit please see application note DAN108 on EXAR’s web site.
TABLE 3: INTA AND INTB PINS OPERATION FOR TRANSMITTER
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1
(FIFO ENABLED)
INTA/B Pin
0 = a byte in THR
1 = THR empty
0 = at least 1 byte in FIFO
1 = FIFO empty
TABLE 4: INTA AND INTB PIN OPERATION FOR RECEIVER
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1
(FIFO ENABLED)
INTA/B Pin
0 = no data
1 = 1 byte
0 = FIFO below trigger level
1 = FIFO above trigger level
C1
22-47 pF
C2
22-47 pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500Κ1Μ
XTAL1
XTAL2
相关PDF资料 |
PDF描述 |
|---|---|
| ST16C552CJ68 | 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68 |
| ST16C554DCJ68 | 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| ST1803DHI | High Voltage Fast-Switching NPN Power Transistor(高电压快速开关NPN功率晶体管) |
| ST180S16P1PBF | 314 A, 1600 V, SCR, TO-209AB |
| ST1W008S4A | 8 CONTACT(S), MALE, PCMCIA CONNECTOR, SOLDER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C2552CJ44-F | 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2552CJ44TR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C2552CJ44TR-F | 功能描述:UART 接口集成电路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2552CQ48 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| ST16C2552IJ | 制造商:Exar Corporation 功能描述:2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44 |
发布紧急采购，3分钟左右您将得到回复。