- 您现在的位置：买卖IC网 > PDF目录372305 > ST624XB-DBE (意法半导体) REAL TIME EMULATION DEVELOPMENT TOOLS FOR ST6 MCU FAMILY PDF资料下载
参数资料
| 型号： | ST624XB-DBE |
| 厂商： | 意法半导体 |
| 英文描述： | REAL TIME EMULATION DEVELOPMENT TOOLS FOR ST6 MCU FAMILY |
| 中文描述： | 实时仿真开发工具，ST6单片机系列 |
| 文件页数： | 7/74页 |
| 文件大小： | 733K |
| 代理商： | ST624XB-DBE |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页
7/74
ST62T46B/E46B
1.2 PIN DESCRIPTIONS
V
and V
. Power is supplied to the MCU via
these two pins. V
is the power connection and
V
SS
is the ground connection.
OSCin and OSCout.
These pins are internally
connected to the on-chip oscillator circuit. A quartz
crystal, a ceramic resonator or an external clock
signal can be connected between these two pins.
The OSCin pin is the input pin, the OSCout pin is
the output pin.
RESET
. The active-low RESET pin is used to re-
start the microcontroller.
TEST/V
.
The TEST must be held at V
for nor-
mal operation (an internal pull-down resistor se-
lects normal operating mode if TEST pin is not
connected). If TEST pin is connected to a +12.5V
level during the reset phase, the EPROM/OTP
programming Mode is entered.
NMI.
The NMI pin provides the capability for asyn-
chronous interruption, by applying an external non
maskable interrupt to the MCU. Schmitt trigger
characteristics. The user can select as option the
availability of an on-chip pull-up at this pin.
PA4-PA7.
These 4 lines are organised as one I/O
port (A). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs, or
as analog inputs for the A/D converter.
PB0...PB7.
These 8 lines are organised as one I/O
port (B). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs,
analog inputs for the A/D converter. PB0..PB3 can
be used as analog inputs for the A/D converter ,
while PB7/Sout, PB6/Sin and PB5/Scl can be used
respectively as data out, data in and Clock pins for
the on-chip SPI. In addition, PB4..PB7 can sink
20mA for direct LED or TRIAC drive.
PC0-PC7
. These 8 lines are organised as one I/O
port (C). Each line may be configured under soft-
ware control as input with or without internal pull-
up resistor, input with interrupt generation and
pull-up resistor, open-drain or push-pull output, or
as LCD segment output S33..S40.
COM1-COM4
. These four pins are the LCD pe-
ripheral common outputs. They are the outputs of
the on-chip backplane voltage generator which is
used for multiplexing the 45 LCD lines allowing up
to 180 segments to be driven.
S9..S16, S25..S43
. These pins are the 27 LCD pe-
ripheral segment outputs. S33..S40 are alternate
functions of the Port C I/O pins. (Combiports fea-
ture)
VLCD
. Display voltage supply. It determines the
high voltage level on COM1-COM4 and S4-S48
pins.
VLCD1/3, VLCD2/3
. Display supply voltage inputs
for determining the display voltage levels on
COM1-COM4 and S4-S48 pins during multiplex
operation.
PSS
. This is the Power Supply Supervisor sensing
pin. When the voltage applied to this pin is falling
below a software programmed value the highest
priority (NMI) interrupt can be generated. This pin
has to be connected to the voltage to be super-
vised.
OSC32in
and
OSC32out
. These pins are inter-
nally connected with the on-chip 32kHz oscillator
circuit. A 32.768kHz quartz crystal can be con-
nected between these two pins if it is necessary to
provide the LCD stand-by clock and real time inter-
rupt. OSC32in is the input pin, OSC32out is the
output pin.
相关PDF资料 |
PDF描述 |
|---|---|
| ST6263C | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. A/D CONVERTER. SAFE RESET. AUTO-RELOAD TIMER. EEPROM AND SPI |
| ST6265C | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. A/D CONVERTER. SAFE RESET. AUTO-RELOAD TIMER. EEPROM AND SPI |
| ST62E35BG1 | 8-BIT MICROCONTROLLER |
| ST62P08CM3 | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. A/D CONVERTER. OSCILLATOR SAFEGUARD. SAFE RESET AND 20 PINS |
| ST62P08CM6 | 8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. A/D CONVERTER. OSCILLATOR SAFEGUARD. SAFE RESET AND 20 PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST624XB-KIT | 制造商:未知厂家 制造商全称:未知厂家 功能描述:STARTER KIT DATASHEET FOR ST624X |
| ST624XB-KIT/110 | 功能描述:开发板和工具包 - 其他处理器 ST624X Starter Kit RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| ST624XB-KIT/UK | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:ST62 KIT |
| ST6252 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER AND EEPROM |
| ST6252BB1 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER AND EEPROM |
发布紧急采购，3分钟左右您将得到回复。