收藏本站
参数资料
型号： ST72T141K2MAE
厂商： STMICROELECTRONICS
元件分类： 微控制器/微处理器
英文描述： 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34
封装： 0.300 INCH, LEAD FREE, PLASTIC, SOP-34
文件页数： 54/131页
文件大小： 3096K
代理商： ST72T141K2MAE
ST72141K2-Auto
29/131
POWER SAVING MODES (Cont’d)
5.3 WAIT MODE
WAIT mode places the MCU in a low power con-
sumption mode by stopping the CPU.
This power saving mode is selected by calling the
“WFI” ST7 software instruction.
All peripherals remain active. During WAIT mode,
the I bit of the CC register is forced to 0, to enable
all interrupts. All other registers and memory re-
main unchanged. The MCU remains in WAIT
mode until an interrupt or Reset occurs, whereup-
on the Program Counter branches to the starting
address of the interrupt or Reset service routine.
The MCU will remain in WAIT mode until a Reset
or an Interrupt occurs, causing it to wake up.
Refer to Figure 21.
5.4 SLOW MODE
This mode has two targets:
– To reduce power consumption by decreasing the
internal clock in the device,
– To adapt the internal clock frequency (fCPU) to
the available supply voltage.
SLOW mode is controlled by the SMS bit in the
MISCR register. This bit enables or disables Slow
mode selecting the internal slow frequency (fCPU).
In this mode, the oscillator frequency can be divid-
ed by 32 instead of 2 in normal operating mode.
The CPU and peripherals are clocked at this lower
frequency except the Motor Control and the SPI
peripherals which have their own clock selection
bit (XT16) in the MISCR register.
Figure 21. WAIT Mode Flowchart
WFI INSTRUCTION
RESET
INTERRUPT
Y
N
Y
CPU
OSCILLATOR
PERIPHERALS
I BIT
ON
0
OFF
If exit is caused by a RESET, a 4096 CPU
clock cycle delay is inserted.
CPU
OSCILLATOR
PERIPHERALS
ON
OFF*
OFF
Note:
* The peripheral clock is stopped only when exit caused by RESET and not by an interrupt.
** Before servicing an interrupt, the CC register is pushed on the stack.
FETCH RESET VECTOR
OR SERVICE INTERRUPT**
CPU
OSCILLATOR
PERIPHERALS
ON
相关PDF资料
PDF描述
SL28541BQC OTHER CLOCK GENERATOR, QCC64
STM8L101K3T3ATR 8-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQFP32
STM32F103C6T6AXX 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQFP48
STM32F103C8T6XXX 32-BIT, FLASH, 1.25 MHz, RISC MICROCONTROLLER, PQFP48
STM32W108HBU72 SPECIALTY MICROPROCESSOR CIRCUIT, QCC40
相关代理商/技术参数
参数描述
ST72T212G2B6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST72T212G2M6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST72T213G1B6 功能描述:8位微控制器 -MCU OTP EPROM 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST72T213G1M6 功能描述:8位微控制器 -MCU OTP EPROM 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST72T251G1B6 功能描述:8位微控制器 -MCU OTP EPROM 4K SPI/I2C RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*