参数资料
型号: ST7FLCD1G9M1
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO28
封装: ROHS COMPLIANT, SO-28
文件页数: 48/96页
文件大小: 846K
代理商: ST7FLCD1G9M1
IC Single-Master Bus Interface
ST7FLCD1
10
IC Single-Master Bus Interface
10.1
Introduction
The IC Bus Interface serves as an interface between the microcontroller and the serial IC bus. It
provides single-master functions, and controls all IC bus-specific sequencing, protocol and timing.
It supports Fast IC mode (400 kHz) and up to 800 kHz for certain applications.
10.2
Main Features
Parallel / IC bus protocol converter
Interrupt generation
Standard IC mode/Fast IC mode (up to 800 kHz for certain applications)
7-bit Addressing
IC Single Master Mode
End of byte transmission flag
Transmitter /Receiver flag
Clock generation
10.3
General Description
In addition to receiving and transmitting data, this interface converts data from serial to parallel
format and vice versa, using either an interrupt or a polled handshake. The interrupts are enabled or
disabled by software. The interface is connected to the IC bus by a data pin (SDAI) and by a clock
pin (SCLI). It can be connected both with a standard IC bus and a Fast IC bus. This selection is
made by software.
Mode Selection
The interface can operate in the two following modes:
1. Master transmitter/receiver,
2. Idle (default).
The interface automatically switches from Idle to Master mode after it generates a START condition
and from Master to Idle mode after it generates a STOP condition.
Communication Flow
The interface initiates a data transfer and generates the clock signal. A serial data transfer always
begins with a start condition and ends with a stop condition. Both start and stop conditions are
generated by software.
Data and addresses are transferred as 8-bit bytes, MSB first. The first byte following the start
condition is the address byte.
A 9th clock pulse follows the 8 clock cycles of a byte transfer, during which the receiver must send
an acknowledge bit to the transmitter. Refer to Figure 28.
Acknowledge is enabled and disabled by software.
The speed of the IC interface is selected as Standard (0 to 100 kHz) and Fast IC (100 to 400 kHz)
and up to 800 kHz for certain applications.
相关PDF资料
PDF描述
ST7FLIT19BF1U6TR 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, QCC20
ST7FLITE09Y0M1 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO16
ST7FLU05MAE 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO8
ST7LNB0V2Y0M6 8-BIT, 8 MHz, MICROCONTROLLER, PDSO16
ST7LNB1Y0M6 8-BIT, EEPROM, 8 MHz, MICROCONTROLLER, PDSO16
相关代理商/技术参数
参数描述
ST7FLI15BF1U6 功能描述:8位微控制器 -MCU 8-Bit MCU w/ Single Volt Flash RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FLI15BF1U6TR 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FLI19BF1M3TR 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FLI19BF1U6TR 功能描述:8位微控制器 -MCU 8-Bit MCU w/ Single Volt Flash RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FLI19BY1M3TR 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT