参数资料
型号: STM32F105VCT6XXX
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQFP100
封装: 14 X 14 MM, ROHS COMPLIANT, LQFP-100
文件页数: 54/95页
文件大小: 1007K
代理商: STM32F105VCT6XXX
Electrical characteristics
STM32F105xx, STM32F107xx
58/95
Doc ID 15274 Rev 4
5.3.15
Communications interfaces
I
2C interface characteristics
Unless otherwise specified, the parameters given in Table 40 are derived from tests
performed under the ambient temperature, fPCLK1 frequency and VDD supply voltage
conditions summarized in Table 9.
The STM32F105xx and STM32F107xx I
2C interface meets the requirements of the
standard I
2C communication protocol with the following restrictions: the I/O pins SDA and
SCL are mapped to are not “true” open-drain. When configured as open-drain, the PMOS
connected between the I/O pin and VDD is disabled, but is still present.
The I
2C characteristics are described in Table 40. Refer also to Section 5.3.12: I/O port
characteristics for more details on the input/output alternate function characteristics (SDA
and SCL).
Table 40.
I2C characteristics
Symbol
Parameter
Standard mode I2C(1)
1. Guaranteed by design, not tested in production.
Fast mode I2C(1)(2)
2. fPCLK1 must be higher than 2 MHz to achieve the maximum standard mode I
2C frequency. It must be
higher than 4 MHz to achieve the maximum fast mode I2C frequency.
Unit
Min
Max
Min
Max
tw(SCLL)
SCL clock low time
4.7
1.3
s
tw(SCLH)
SCL clock high time
4.0
0.6
tsu(SDA)
SDA setup time
250
100
ns
th(SDA)
SDA data hold time
0(3)
3. The maximum hold time of the Start condition has only to be met if the interface does not stretch the low
period of SCL signal.
0(4)
4. The device must internally provide a hold time of at least 300ns for the SDA signal in order to bridge the
undefined region of the falling edge of SCL.
900(3)
tr(SDA)
tr(SCL)
SDA and SCL rise time
1000
20 + 0.1Cb
300
tf(SDA)
tf(SCL)
SDA and SCL fall time
300
th(STA)
Start condition hold time
4.0
0.6
s
tsu(STA)
Repeated Start condition
setup time
4.7
0.6
tsu(STO)
Stop condition setup time
4.0
0.6
s
tw(STO:STA)
Stop to Start condition time
(bus free)
4.7
1.3
s
Cb
Capacitive load for each bus
line
400
pF
相关PDF资料
PDF描述
STM32F105VBT6TR 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQFP100
STM32F105VCT7TR 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQFP100
STM32F105V8T6XXX 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQFP100
STM32F105VCT6TR 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQFP100
STM32F107RBT6XXX 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
STM32F105VCT7 功能描述:ARM微控制器 - MCU 32-Bit Cortex 64Kb Connectivity Line RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
STM32F107RB 制造商:STMicroelectronics 功能描述:
STM32F107RBT6 功能描述:ARM微控制器 - MCU 32BIT Cortex 64/25 CONNECTIVITY LINE M3 RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
STM32F107RCT6 功能描述:ARM微控制器 - MCU 32BIT Cortex 64/25 CONNECTIVITY LINE M3 RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT
STM32F107RCT6TR 功能描述:ARM微控制器 - MCU 32BIT CORTEX M3 256K Flash 6KB RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT