- 您现在的位置：买卖IC网 > PDF目录380771 > STM704TDS6F (意法半导体) 3V Supervisor with Battery Switchover PDF资料下载
参数资料
| 型号： | STM704TDS6F |
| 厂商： | 意法半导体 |
| 英文描述： | 3V Supervisor with Battery Switchover |
| 中文描述： | 3V的监控与电池切换 |
| 文件页数： | 9/31页 |
| 文件大小： | 194K |
| 代理商： | STM704TDS6F |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
9/31
STM690/704/795/802/804/805/806
OPERATION
Reset Output
The STM690/704/795/802/804/805/806 Supervi-
sor asserts a reset signal to the MCU whenever
V
CC
goes below the reset threshold (V
RST
), a
watchdog time-out occurs, or when the Push-but-
ton Reset Input (MR) is taken low. RST is guaran-
teed to be a logic low (logic high for STM804/805)
for 0V < V
CC
< V
RST
if V
BAT
is greater than 1V.
Without a back-up battery, RST is guaranteed val-
id down to V
CC
=1V.
During power-up, once V
CC
exceeds the reset
threshold an internal timer keeps RST low for the
reset time-out period, t
rec
. After this interval RST
returns high.
If V
CC
drops below the reset threshold, RST goes
low. Each time RST is asserted, it stays low for at
least the reset time-out period (t
rec
). Any time V
CC
goes below the reset threshold the internal timer
clears. The reset timer starts when V
CC
returns
above the reset threshold.
Push-button Reset Input (STM704/806)
A logic low on MR asserts reset. Reset remains
asserted while MR is low, and for t
rec
(see
Figure
36., page 22
) after it returns high. The MR input
has an internal 40k
pull-up resistor, allowing it to
be left open if not used. This input can be driven
with TTL/CMOS-logic levels or with open-drain/
collector outputs. Connect a normally open mo-
mentary switch from MR to GND to create a man-
ual reset function; external debounce circuitry is
not required. If MR is driven from long cables or
the device is used in a noisy environment, connect
a 0.1μF capacitor from MR to GND to provide ad-
ditional noise immunity. MR may float, or be tied to
V
CC
when not used.
Watchdog Input (NOT available on STM704/
795/806)
The watchdog timer can be used to detect an out-
of-control MCU. If the MCU does not toggle the
Watchdog Input (WDI) within t
WD
(1.6sec typ), the
reset is asserted. The internal watchdog timer is
cleared by either:
1.
a reset pulse, or
2.
by toggling WDI (high-to-low or low-to-high),
which can detect pulses as short as 50ns. If
WDI is tied high or low, a reset pulse is
triggered every 1.8sec (t
WD
+ t
rec
).
The timer remains cleared and does not count for
as long as reset is asserted. As soon as reset is re-
leased, the timer starts counting (see
Figure
37., page 23
).
Note:
Input frequency greater than 20ns (50MHz)
will be filtered.
Back-up Battery Switchover
In the event of a power failure, it may be necessary
to preserve the contents of external SRAM
through V
OUT
. With a backup battery installed with
voltage V
BAT
, the devices automatically switch the
SRAM to the back-up supply when V
CC
falls.
Note:
If back-up battery is not used, connect both
V
BAT
and V
OUT
to V
CC
.
This family of Supervisors does not always con-
nect V
BAT
to V
OUT
when V
BAT
is greater than V
CC
.
V
BAT
connects to V
OUT
(through a 100
switch)
when V
CC
is below V
SW
(2.4V) or V
BAT
(whichever
is lower). This is done to allow the back-up battery
(e.g., a 3.6V lithium cell) to have a higher voltage
than V
CC
.
Assuming that V
BAT
> 2.0V, switchover at V
SO
en-
sures that battery back-up mode is entered before
V
OUT
gets too close to the 2.0V minimum required
to reliably retain data in most external SRAMs.
When V
CC
recovers, hysteresis is used to avoid
oscillation around the V
SO
point. V
OUT
is connect-
ed to V
CC
through a 3
PMOS power switch.
Note:
The back-up battery may be removed while
V
CC
is valid, assuming V
BAT
is adequately decou-
pled (0.1μF typ), without danger of triggering a re-
set.
Table 4. I/O Status in Battery Back-up
Pin
Status
V
OUT
Connected to V
BAT
through internal switch
V
CC
Disconnected from V
OUT
PFI
Disabled
PFO
Logic Low
E
High impedance
E
CON
Logic High
WDI
Watchdog timer is disabled
MR
Disabled
RST
Logic Low
RST
Logic High
V
BAT
Connected to V
OUT
Vccsw
Logic High (STM795)
相关PDF资料 |
PDF描述 |
|---|---|
| STM704TM6E | 3V Supervisor with Battery Switchover |
| STM704TM6F | 3V Supervisor with Battery Switchover |
| STM795RDS6E | 3V Supervisor with Battery Switchover |
| STM795RDS6F | 3V Supervisor with Battery Switchover |
| STM795RM6E | 3V Supervisor with Battery Switchover |
相关代理商/技术参数 |
参数描述 |
|---|---|
| STM704TM6E | 功能描述:监控电路 3V Supervisor w/Battery Switchover RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| STM704TM6F | 功能描述:监控电路 4.40V w/Batt Switch RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| STM705 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5V Supervisor |
| STM705_10 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5 V supervisor |
| STM705ADS6E | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5 V supervisor |
发布紧急采购，3分钟左右您将得到回复。