- 您现在的位置：买卖IC网 > PDF目录98149 > SX28AC/SSU 2 CHANNEL(S), I2C BUS CONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | SX28AC/SSU |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 2 CHANNEL(S), I2C BUS CONTROLLER, PDSO28 |
| 封装： | GREEN, PLASTIC, SSOP-28 |
| 文件页数： | 3/48页 |
| 文件大小： | 772K |
| 代理商： | SX28AC/SSU |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
2005 Ubicom, Inc. All rights reserved.
- 11 -
www.ubicom.com
SX20AC/SX28AC
4.0 SPECIAL-FUNCTION REGISTERS
The CPU uses a set of special-function registers to con-
trol the operation of the device.
The CPU registers include an 8-bit working register (W),
which serves as a pseudo accumulator. It holds the sec-
ond operand of an instruction, receives the literal in
immediate type instructions, and also can be program-
selected as the destination register.
A set of 31 file registers serves as the primary accumula-
tor. One of these registers holds the first operand of an
instruction and another can be program-selected as the
destination register. The first eight file registers include
the Real-Time Clock/Counter register (RTCC), the lower
eight bits of the 11-bit Program Counter (PC), the 8-bit
STATUS register, three port direction registers for Port A,
Port B, Port C, the 8-bit File Select Register (FSR), and
INDF used for indirect addressing.
The five low-order bits of the FSR register select one of
the 31 file registers in the indirect addressing mode. Call-
ing for the file register located at address 00h (INDF) in
any of the file-oriented instructions selects indirect
addressing, which uses the FSR register. It should be
noted that the file register at address 00h is not a physi-
cally implemented register. The CPU also contains an 8-
level, 11-bit hardware push/pop stack for subroutine link-
age.
*In the SX20 package, Port C is not used, and address
07h is available as a general-purpose RAM location.
4.1 PC Register (02h)
The PC register holds the lower eight bits of the program
counter. It is accessible at run time to perform branch
operations.
4.2 STATUS Register (03h)
The STATUS register holds the arithmetic status of the
ALU, the page select bits, and the reset state. The
STATUS register is accessible during run time, except
that bits PD and TO are read-only. It is recommended
that only SETB and CLRB instructions be used on this
register. Care should be exercised when writing to the
STATUS register as the ALU status bits are updated
upon completion of the write operation, possibly leaving
the STATUS register with a result that is different than
intended. For instance, a CLR STATUS command will set
the Z bit as expected, but may leave bits 4, 3, 1, and 0
unchanged.
Table 4-1. Special-Function Registers
Addr
Name
Function
00h
INDF
Used for indirect addressing
01h
RTCC
Real Time Clock / Counter
(or W; see OPTION bit 7)
02h
PC
Program Counter (low byte)
03h
STATUS
Holds Status bits of ALU
04h
FSR
File Select Register
05h
RA
Port RA Data register
06h
RB
Port RB Data register
07h
RC*
Port RC Data register
08-0Fh
General Data RAM
PA2
PA1
PA0
TO
PD
Z
DC
C
Bit 7
Bit 0
Bit 7-5: Page select bits PA2:PA0
000 = Page 0 (000h – 01FFh)
001 = Page 1 (200h – 03FFh)
010 = Page 2 (400h – 05FFh)
011 = Page 3 (600h – 07FFh)
Bit 4:
Time Out bit, TO (read only)
1 = Set to 1 after power up and upon exe-
cution of CLR !WDT or SLEEP instructions
0 = A watchdog time-out occurred
Bit 3:
Power Down bit, PD (read only)
1= Set to a 1 after power up and upon ex-
ecution of the CLR !WDT instruction
0 = Cleared to a ‘0’ upon execution of
SLEEP instruction
Bit 2:
Zero bit, Z (see Table 16-1, last column)
1 = Result of operation is zero
0 = Result of operation is non-zero
Bit 1:
Digit Carry bit, DC (see Table 16-1, last column)
After Addition:
1 = A carry from bit 3 occurred
0 = No carry from bit 3 occurred
After Subtraction:
1 = No borrow from bit 3 occurred
0 = A borrow from bit 3 occurred
Bit 0:
Carry bit, C (see Table 16-1, last column)
After Addition:
1 = A carry from bit 7 of the result occurred
0 = No carry from bit 7 of the result
occurred
After Subtraction:
1 = No borrow from bit 7 of the result
occurred
0 = A borrow from bit 7 of the result
occurred
Rotate (RR or RL) Instructions:
The carry bit is loaded with the low or high
order bit, respectively. When CF bit is
cleared, Carry bit works as input for ADD
and SUB instructions.
相关PDF资料 |
PDF描述 |
|---|---|
| SY100EP11UZITR | 100E SERIES, LOW SKEW CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| SY100EP195VTCTR | ACTIVE DELAY LINE, COMPLEMENTARY OUTPUT, PQFP32 |
| SY100EP195VTG | ACTIVE DELAY LINE, COMPLEMENTARY OUTPUT, PQFP32 |
| SY100EP196VTCTR | ACTIVE DELAY LINE, COMPLEMENTARY OUTPUT, PQFP32 |
| SY100EP196VTC | ACTIVE DELAY LINE, COMPLEMENTARY OUTPUT, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SX28AD100-I/DP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AD100-I/PQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AD100-I/SO | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AD100-I/SS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
| SX28AD100-I/TQ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configurable Communications Controllers with EE/Flash Program Memory, In-System Programming Capability and On-Chip Debug |
发布紧急采购，3分钟左右您将得到回复。