- 您现在的位置：买卖IC网 > PDF目录98159 > TAS5026CPAG (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP64 PDF资料下载
参数资料
| 型号： | TAS5026CPAG |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封装： | PLASTIC, TQFP-64 |
| 文件页数： | 16/52页 |
| 文件大小： | 886K |
| 代理商： | TAS5026CPAG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
Architecture Overview
18
SLES041B—November 2002
TAS5026
While a volume update is being performed, the system status register indicates that the update is in progress.
During the update, all subsequent volume control setting requests that are sent to the TAS5026 are received
and stored as a single next value for a subsequent update. If more than one volume setting request is sent,
only the last is retained.
Table 2–9. Volume Register
VOLUME REGISTER
D 7
D 6
D 5
D 4
D 3
D 2
D 1
D 0
Vol
Bit 7
Vol
Bit 6
Vol
Bit 5
Vol
Bit 4
Vol
Bit 3
Vol
Bit 2
Vol
Bit 1
Vol
Bit 0
2.3.2 Mute
The application of mute ramps the volume from any setting to noiseless hard mute state. There are two
methods in which the TAS5026 can be placed into mute. The TAS5026 is placed in the noiseless mute when
the MUTE terminal is asserted low for a minimum of 3 MCLK_IN cycles. Alternatively, the mute mode can be
initiated by setting the mute bit in the system control register through the serial control interface. The TAS5026
is held in mute state as long as the terminal is low or I2C mute setting is active. This command uses quiet entry
and exit sequences to and from the hard mute state.
If an error recovery (described in the PWM section) occurs after a mute request has been received, the device
returns from error recovery with the channel volume set as specified by the mute command.
2.3.3 Auto Mute
Auto mute is an automatic sequence that can be enabled or disabled via the serial control interface. The
default for this control is enabled. When enabled, the PWM auto mutes an individual channel when a channel
receives from 5 ms to 50 ms of consecutive zeros. This time interval can be selectable using the auto mute
delay register. The default interval is 5 ms at 48 kHz. This duration is independent of the sample rate. The auto
mute state is exited when two consecutive samples of nonzero data are received.
This mode uses the valid low to provide a low-noise floor while maintaining a short startup time. Noise free
entry and exit is achieved by using the PWM quiet start and stop sequences.
2.3.4 Individual Channel Mute
Individual channel mute is invoked through the serial interface. Individual channel mute permits each channel
of the TAS5026 to be individually muted and unmuted. The operation that is performed is identical to the mute
operation; however, it is performed on a per channel basis. A TAS5026 channel is held in the mute state as
long as the serial interface mute setting for that channel is set.
2.3.5 De-Emphasis Filter
For audio sources that have been pre-emphasized, a precision 50-
s/15-s de-emphasis filter is provided to
support the sampling rates of 32 kHz, 44.1 kHz, and 48 kHz. See Figure 2–11 for a graph showing the
de-emphasis filtering characteristics. De-emphasis is set using two bits in the system control register.
Table 2–10. De-Emphasis Filter Characteristics
DEM_SEL2 (MSB)
DEM_SEL1
DESCRIPTION
0
De-emphasis disabled
0
1
De-emphasis enabled for Fs = 48 kHz
1
0
De-emphasis enabled for Fs = 44 kHz
1
De-emphasis enabled for Fs = 32 kHz
Following the change of state of the de-emphasis bits, the PWM outputs go into the soft mute state. After 128
LRCLK periods for initialization, the PWM outputs are driven to the normal (unmuted) mode.
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5026PAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5026PAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5026PAGG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5026IPAGRG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5026IPAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5026IPAG | 功能描述:多媒体杂项 Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 类型: 通道数量: 转换速率:540 Mbps 分辨率: 封装 / 箱体:SOIC-16 封装:Tube |
| TAS5026IPAGG4 | 功能描述:多媒体杂项 Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 类型: 通道数量: 转换速率:540 Mbps 分辨率: 封装 / 箱体:SOIC-16 封装:Tube |
| TAS5026IPAGR | 功能描述:多媒体杂项 Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 类型: 通道数量: 转换速率:540 Mbps 分辨率: 封装 / 箱体:SOIC-16 封装:Tube |
| TAS5026IPAGRG4 | 功能描述:多媒体杂项 Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 类型: 通道数量: 转换速率:540 Mbps 分辨率: 封装 / 箱体:SOIC-16 封装:Tube |
| TAS5026PAG | 功能描述:多媒体杂项 Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 类型: 通道数量: 转换速率:540 Mbps 分辨率: 封装 / 箱体:SOIC-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。