参数资料
| 型号： | TC530CPJ |
| 厂商： | Microchip Technology |
| 文件页数： | 4/28页 |
| 文件大小： | 0K |
| 描述： | IC DATA ACQ SUBSYSTEM 28DIP |
| 标准包装： | 15 |
| 类型： | 数据采集系统（DAS） |
| 分辨率（位）： | 17 b |
| 采样率（每秒）： | 6.5 |
| 数据接口： | 串行 |
| 电压电源： | 单电源 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 28-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 28-DIP |
| 包装： | 管件 |
| 其它名称： | Q1000542A |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
TC530/TC534
DS21433C-page 12
2007 Microchip Technology Inc.
5.0
TYPICAL APPLICATIONS
5.1
Programming the TC530/TC534
5.1.1
AZ AND INT PHASE DURATION
These two phases have equal duration determined by
the crystal (or external) frequency and the timer initial-
ization byte (LOAD VALUE). Timing is selected as
follows:
1.
Select Integration Time
Integration time must be picked as a multiple of
the period of the line frequency. For example,
TINT times of 33 ms, 66 ms and 132 ms
maximize 60 Hz line rejection.
2.
Estimate Crystal Frequency
Crystal frequencies as high as 2 MHz are
allowed. Crystal frequency is estimated using:
EQUATION 5-1:
3.
Calculate LOAD VALUE
EQUATION 5-2:
FIN can be adjusted to a standard value during this
step. The resulting base, -10 LOAD VALUE, must be
converted to a hexadecimal number and then loaded
into the serial port prior to initiating A/D conversion.
5.2
DINT and IZ Phase Timing
The duration of the DINT phase is a function of the
amount of voltage stored on the integrator capacitor
during INT and the value of VREF. The DINT phase is
initiated immediately following INT and terminated
when an integrator output zero crossing is detected. In
general, the maximum number of counts chosen for
DINT is twice that of INT (with VREF chosen at
VIN(MAX)/2).
5.3
System RESET
The TC530/TC534 must be forced into the AZ state
when power is first applied. A .01 F capacitor
connected from RESET to VDD (or external system
reset logic signal) can be used to momentarily drive
RESET high for a minimum of 100 ms.
5.4
Design Example
Figure 5-1 shows a typical TC530 interrupt-driven
application. Timing and component values are
calculated from equations and recommendations made
of this document. The EOC connection to the
processor INT input is for interrupt-driven applications
only. (In polled systems, the EOC output is available on
DOUT).
Given:
1.
Pick Integration time (TINT): 66 ms.
2.
Estimate crystal frequency.
EXAMPLE 5-1:
3.
Calculate LOAD VALUE
EXAMPLE 5-2:
4.
Calculate RINT.
EXAMPLE 5-3:
5.
Calculate CINT for maximum (4V) integrator out-
put swing:
2(RES)/TINT
Where:
RES
=
Desired Converter Resolution (in
counts)
FIN
=
Input Frequency (in MHz)
INT
=
Integration Time (in seconds)
[LOAD VALUE]10
256
TINT
() F
IN
()
1024
------------------------------
–
=
Required Resolution
(RES):
16-bits (65,536 counts.)
Maximum: VIN ±2V
Power Supply Voltage: +5V
60Hz System
FIN
2RES
TINT
------------
2 65536
66ms
----------------------- 2MHz
≈
==
LOAD VALUE
256
TINT
() F
IN
()
1024
------------------------------
–
128
[]
10
==
128
[]
10
80 hex
=
RINT
VINMAX
20
-------------------
2
20
------
100k
Ω
==
=
相关PDF资料 |
PDF描述 |
|---|---|
| MS3108A20-33P | CONN PLUG 11POS RT ANG W/PINS |
| M83723/83W1814N | CONN RCPT 14POS WALL MT W/PINS |
| MAX180AEPL+ | IC DAS 12BIT 100KSPS 40-DIP |
| M83723/83R1814N | CONN RCPT 14POS WALL MT W/PINS |
| MS27473E22B55PD | CONN PLUG 55POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC531000AP-F711 | 制造商:Toshiba America Electronic Components 功能描述:531000AP-F711 |
| TC531001 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:1M BIT (128K WORD x 8 BIT) CMOS MASK ROM |
| TC531001CF | 制造商:Toshiba America Electronic Components 功能描述: |
| TC531001CF-12 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:1M BIT (128K WORD x 8 BIT) CMOS MASK ROM |
| TC531001CF-15 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:1M BIT (128K WORD x 8 BIT) CMOS MASK ROM |
发布紧急采购，3分钟左右您将得到回复。