- 您现在的位置：买卖IC网 > PDF目录98178 > TC7126RIPL 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 PDF资料下载
参数资料
| 型号： | TC7126RIPL |
| 元件分类： | ADC |
| 英文描述： | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| 封装： | REVERSE, PLASTIC, DIP-40 |
| 文件页数： | 7/26页 |
| 文件大小： | 413K |
| 代理商： | TC7126RIPL |
2006 Microchip Technology Inc.
DS21458C-page 15
TC7126/A
7.3
Analog Common (Pin 32)
The analog common pin is set at a voltage potential
approximately 3V below V+. The potential is between
2.7V and 3.35V below V+. Analog common is tied inter-
nally to an N-channel FET capable of sinking 100
μA.
This FET will hold the common line at 3V should an
external load attempt to pull the common line toward
V+. Analog common source current is limited to 1
μA.
Therefore, analog common is easily pulled to a more
negative voltage (i.e., below V+ – 3V).
The TC7126A connects the internal VIN+ and VIN-
inputs to analog common during the auto-zero phase.
During the reference integrate phase, VIN- is con-
nected to analog common. If VIN- is not externally con-
nected to analog common, a Common mode voltage
exists, but is rejected by the converter’s 86dB Common
mode rejection ratio. In battery operation, analog com-
mon and VIN- are usually connected, removing Com-
mon mode voltage concerns. In systems where VIN- is
connected to power supply ground or to a given
voltage, analog common should be connected to VIN-.
The analog common pin serves to set the analog sec-
tion reference, or common point. The TC7126A is spe-
cifically designed to operate from a battery, or in any
measurement system where input signals are not refer-
enced (float) with respect to the TC7126A’s power
source. The analog common potential of V+ – 3V gives
a 7V end of battery life voltage. The common potential
has a 0.001%/% voltage coefficient and a 15
Ω output
impedance.
With sufficiently high total supply voltage (V+ – V- > 7V),
analog common is a very stable potential with excellent
temperature stability (typically 35ppm/°C). This poten-
tial can be used to generate the TC7126A’s reference
voltage. An external voltage reference will be unneces-
sary in most cases because of the 35ppm/°C tempera-
ture coefficient. See Section 7.5 “TC7126A Internal
TC7126A
Internal
Voltage
Reference discussion.
7.4
TEST (Pin 37)
The TEST pin potential is 5V less than V+. TEST may
be used as the negative power supply connection for
external CMOS logic. The TEST pin is tied to the inter-
nally generated negative logic supply through a 500
Ω
resistor. The TEST pin load should be no more than
1mA. See Section 5.0 “DIGITAL SECTION”, Digital
Section for additional information on using TEST as a
negative digital logic supply.
If TEST is pulled HIGH (to V+), all segments plus the
minus sign will be activated. DO NOT OPERATE IN
THIS MODE FOR MORE THAN SEVERAL MINUTES.
With TEST = V+, the LCD segments are impressed
with a DC voltage which will destroy the LCD.
7.5
TC7126A Internal Voltage
Reference
The TC7126A’s analog common voltage temperature
stability has been significantly improved (Figure 7-3).
The “A” version of the industry standard TC7126 device
allows users to upgrade old systems and design new
systems, without external voltage references. External
R and C values do not need to be changed. Figure 7-4
shows analog common supplying the necessary
voltage reference for the TC7126A.
FIGURE 7-3:
Analog Common Temp.
Coefficient
FIGURE 7-4:
TC7126A Internal Voltage
Reference Connection
Typical
Maximum
Typical
200
180
160
140
120
100
80
60
40
20
0
Analog
Commom
T
e
mperature
Coefficient
(ppm/°C)
TC7126A
ICL7136
No
Maximum
Specified
No
Maximum
Specified
ICL7126
V-
ANALOG
COMMON
TC7126A
VREF+
32
35
36
26
240k
Ω
10k
Ω
VREF-
VREF
1
+
9V
SET VREF = 1/2 VREF
V+
相关PDF资料 |
PDF描述 |
|---|---|
| TC7126RCLW | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44 |
| TC7126ACPL | 1-CH DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP40 |
| TC7129CKW | 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44 |
| TC7129CLWTR | 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC44 |
| TC7129CJL | 1-CH DUAL-SLOPE ADC, CDIP40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC7129 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4-1/2 Digit Analog-to-Digital Converters with On-Chip LCD Drivers |
| TC7129_06 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4-1/2 Digit Analog-to-Digital Converters with On-Chip LCD Drivers |
| TC7129_13 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4-1/2 Digit Analog-to-Digital Converters with On-Chip LCD Drivers |
| TC7129CJL713 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:4-1/2 Digit Analog-to-Digital Converters with On-Chip LCD Drivers |
| TC7129CKW | 功能描述:LCD 驱动器 w/LCD Driver RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。