- 您现在的位置：买卖IC网 > PDF目录98185 > TC9446FG SPECIALTY CONSUMER CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | TC9446FG |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封装： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 40/41页 |
| 文件大小： | 562K |
| 代理商： | TC9446FG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页
TC9446FG
2005-09-28
8
2.
Data Transmission Format
2-1.
Serial Mode Setting
2-1-1. Data Transmission Format in the Serial Mode
A data transmission format in the serial mode is shown in Figure 1.
After the data transmission at the time of the serial mode sets MICS signal to “L”, fundamentally, it checks that MIACK signal is “L” and transmits a 24 bit
command at MSB first.
However, it cannot transmit at the time of MIACK signal = “H”.
Then, the word set up by the 24 bit command which the Read or Write (R/W) of 24 bit data of a number (1-16 word) is performed, and, finally, MICS signal is
set to “H”.
However, since there is a term when MIACK signal after transmission is set to “H” in a 24 bit command, at the time of Read, command transmission back also
needs to check that MIACK signal is set to “L”.
2-1-2. Data Transmission Method in the Serial Transmission Mode
1)
Program boot and a program start
As for TC9446FG, RAM is assigned 128 words of program address 0000h-007Fh, and the interruption vector address is become 0000h-0009h.
Therefore, in order to operate TC9446FG, it needs to interrupt and a program needs to be booted to a vector address. In addition, a program load needs to be
continuously performed to an interruption vector address to store a program in 000Ah-007Fh.
In order to perform program boot, the program RAM boot start bit and the soft reset bit in the 24 bit command transmitted after reset need to be set to “H”.
(command = 000060h) And, after command transmission, program data (40 bit) is divided into 20 bit of a higher rank/low rank, and it transmits by the low-rank
stuffing of 24 bit data in the order of a higher rank (20 bit) and a low rank (20 bit).
Since a write-in address is made automatic (+1) from 0000h, if it transmits the required number of words and MICS is set to “H”, program boot will complete
it.
In addition, the write-in address of program boot always starts from 0000h.
A start of a program carries out and transmits the soft reset bit in a 24 bit command to “L”, and is performed by setting MICS to “H”, without performing
data transmission.
The procedure of program boot and a program start is shown in Figure 2.
Figure 1
Serial Mode Data Transmission Format
Transmission data (1 to 16 words)
MICS
MIACK
MILP
MICK
MIDIO
COMMAND (24 bit)
DATA-1 (24 bit)
DATA-16 (24 bit)
相关PDF资料 |
PDF描述 |
|---|---|
| TC9447F | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| TC9452F | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| TC9456F | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| TC9459F | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TC9459N | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDIP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC9447F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:Single-Chip Audio Digital Signal Processor |
| TC9452F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:SINGLE CHIP SURROUND LSI |
| TC9455F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic |
| TC9455N | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic |
| TC9456F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:SINGLE CHIP SURROUND LSI WITH A BUILT-IN SRS |
发布紧急采购，3分钟左右您将得到回复。