- 您现在的位置：买卖IC网 > PDF目录98185 > TC9446FG SPECIALTY CONSUMER CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | TC9446FG |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封装： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 5/41页 |
| 文件大小： | 562K |
| 代理商： | TC9446FG |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
TC9446FG
2005-09-28
13
5)
Incorrect operation detection
Incorrect operation detection of the internal program of TC9446FG can be made to perform by
setting the incorrect operation detection start bit in a 24 bit command to “H”. As for this incorrect
operation detection start bit, the reversal output only of the case of MICS terminal = “H” is carried
out from MIACK terminal.
And, since this incorrect operation detection start bit is periodically cleared by “L” when an internal
program is operating normally, MIACK terminal at the time of MICS terminal = “H” is set to “H”
from “L”.
However, since it will stop being cleared if an internal program becomes a incorrect operation state,
as for MIACK terminal at the time of MICS terminal = “H”, the state of “L” will continue.
Thus incorrect operation detection of a program is attained by supervising MIACK terminal at the
time of MICS terminal = “H”. Moreover, although it checks that MIACK terminal is “L” after setting
MICS terminal to “L” in case a MCU starts access to TC9446FG, MCU can judge that an internal
program is a incorrect operation state, when the state of MIACK = “H” continues.
In addition, when a incorrect operation state is detected, it can return from a incorrect operation
state by initializing by transmitting the soft reset command which the reset terminal was set to “L” or
was mentioned above.
The procedure of incorrect operation detection is shown in Figure 6.
Figure 6
Procedure of Incorrect Operation Detection
MICS
= “L”
Checking of MIACK
= “L”
(waiting for becoming to MIACK
= “L” at the MIACK = “H”)
Transmission of 24 bit command
(starting the incorrect operation detection
= 000080h)
Program makes to clear the incorrect operation
detection bit
MIACK
= “H”
It starts the incorrect operation detection
by “1”.
MICS
= “H”
MIACK
= “L”
When not set to “L” with “H”, it is the state
of incorrect operation.
MIACK
= “L” is continue at incorrect
operation, as detection bit isn’t cleared.
相关PDF资料 |
PDF描述 |
|---|---|
| TC9447F | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| TC9452F | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| TC9456F | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| TC9459F | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| TC9459N | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDIP28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TC9447F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:Single-Chip Audio Digital Signal Processor |
| TC9452F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:SINGLE CHIP SURROUND LSI |
| TC9455F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic |
| TC9455N | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic |
| TC9456F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:SINGLE CHIP SURROUND LSI WITH A BUILT-IN SRS |
发布紧急采购，3分钟左右您将得到回复。