- 您现在的位置：买卖IC网 > PDF目录85415 > TDA6111Q/N4 (NXP SEMICONDUCTORS) 1 CHANNEL, VIDEO AMPLIFIER, PZFM9 PDF资料下载
参数资料
| 型号： | TDA6111Q/N4 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PZFM9 |
| 封装： | PLASTIC, SOT-111, DIL-BENT-SIL, 9 PIN |
| 文件页数： | 16/18页 |
| 文件大小： | 114K |
| 代理商： | TDA6111Q/N4 |
1995 Feb 07
7
Philips Semiconductors
Preliminary specication
Video output amplier
TDA6111Q
Notes
1. If the difference between VDDL and Vip is less than 7 V, overshoot cannot be specified.
2. SVRR: The ratio of the change in supply voltage to the change in input voltage when there is no change in output
voltage.
Ov
cathode output voltage overshoot
VocAC = 100 V (p-p);
VocDC = 100 V square
wave; f < 1 MHz;
tr =tf =22ns;
see Figs 4 and 5; note 1
9
%
SVRRH
high supply voltage rejection ratio
f < 50 kHz; note 2
85
dB
SVRRL
low supply voltage rejection ratio
f < 50 kHz; note 2
70
dB
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Cathode output
The cathode output is protected against peak currents
(caused by positive voltage peaks during high-resistance
flash) of 5 A maximum with a charge content of 100
C.
The cathode is also protected against peak currents
(caused by positive voltage peaks during low-resistance
flash) of 10 A maximum with a charge content of 100 nC.
Flashover protection
The TDA6111Q incorporates protection diodes against
CRT flashover discharges that clamp the cathode output
pin to the VDDH pin. The DC supply voltage at the VDDH pin
has to be within the operating range of 180 to 210 V to
ensure that the Absolute Maximum Rating for VDDH of
250 V will not be exceeded during flashover. To limit the
diode current, an external 680
carbon high-voltage
resistor in series with the cathode output and a 2 kV spark
gap are needed (for this resistor-value, the CRT has to be
connected to the main PCB). This addition produces an
increase in the rise and fall times of approximately 5 ns
and a decrease in the overshoot of approximately 4%.
VDDH to GND must be decoupled:
1. With a capacitor >20 nF with good HF behaviour
(e.g. foil). This capacitance must be placed as close
as possible to pins 6 and 4, but definitely within 5 mm.
2. With a capacitor >10
F on the picture tube base print
(common for three output stages).
VDDL to GND must be decoupled:
1. With a capacitor >20 nF with good HF behaviour
(e.g. ceramic). This capacitance must be placed as
close as possible to pins 2 and 4, but definitely within
10 mm.
Switch-off behaviour
The switch-off behaviour of the TDA6111Q is defined:
when the bias current becomes zero, at VDDL (pin 2) lower
than approximately 5 V, all the output pins
(pins 7, 8 and 9) will be high.
相关PDF资料 |
PDF描述 |
|---|---|
| TDA8822M/C1 | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| TDA8822MDB-T | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| TDA8822MDB | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| TDA8822T/C1 | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| TDA8822TD | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA6111QU | 功能描述:视频放大器 VIDEO OUTPUT AMP RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| TDA6118JF/N1 | 制造商:NXP Semiconductors 功能描述:6118JF/N1 制造商:Philips E C G Inc 功能描述:6118JF/N1 |
| TDA6118JF-N2 | 制造商:Panasonic Industrial Company 功能描述:IC |
| TDA6120 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Video output amplifier |
| TDA6120Q | 制造商:Panasonic Industrial Company 功能描述:SUB ONLY P-C1AA00000326 IC SUBBING WITH C1AA00000326 |
发布紧急采购，3分钟左右您将得到回复。