参数资料
型号: TDA6650ATT/C3
厂商: NXP SEMICONDUCTORS
元件分类: 消费家电
英文描述: SPECIALTY CONSUMER CIRCUIT, PDSO38
封装: 4.40 MM, 0.50 MM PITCH, PLASTIC, MO-153, SOT510-1, TSSOP-38
文件页数: 22/54页
文件大小: 325K
代理商: TDA6650ATT/C3
TDA6650ATT_6651ATT_2
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 02 — 2 February 2007
29 of 54
NXP Semiconductors
TDA6650ATT; TDA6651ATT
5 V mixer/oscillator and low noise PLL synthesizer
[4]
The RF frequency range is dened by the oscillator frequency range and the Intermediate Frequency (IF).
[5]
The 1 % cross modulation performance is measured with AGC detector turned off (AGC bits set to 110).
[6]
The IF output signal stays stable within the range of the step frequency for any RF input level up to 120 dB
V.
[7]
Limits are related to the tank circuits used in Figure 27 and 28 for digital application or Figure 29 and 30 for hybrid application.
Frequency bands may be adjusted by the choice of external components.
[8]
The frequency shift is dened as a change in oscillator frequency when the supply voltage varies from VCC = 5 V to 4.5 V or from
VCC = 5 V to 5.25 V. The oscillator is free running during this measurement.
[9]
The frequency drift is dened as a change in oscillator frequency when the ambient temperature varies from Tamb =25 °C to 50 °C or
from Tamb =25 °C to 0 °C. The oscillator is free running during this measurement.
[10] The supply ripple susceptibility is measured in the measurement circuit according to Figure 27 to Figure 30 using a spectrum analyzer
connected to the IF output. An unmodulated RF signal is applied to the test board RF input. A sine wave signal with a frequency of
500 kHz is superimposed onto the supply voltage. The amplitude of this ripple signal is adjusted to bring the 500 kHz sidebands around
the IF carrier to a level of
53.5 dB with respect to the carrier.
[11] This is the level of divider interferences close to the IF frequency. The low and mid band inputs must be left open (i.e. not connected to
any load or cable); the high band inputs are connected to an hybrid.
[12] Crystal oscillator interference means the 4 MHz sidebands caused by the crystal oscillator.
[13] The step frequency rejection is the level of step frequency sidebands related to the carrier. The measurement is done for
VIF = 100 dBV. This specication point corresponds to the worst case observed in the frequency range. This parameter is specied for
fstep = 142.86 kHz in digital applications and fstep = 62.5 kHz, 50 kHz or 142.86 kHz in hybrid application.
[14] This is the level of the 13rd and 15th harmonics of the 4 MHz crystal oscillator into the IF output.
[15] The AGC pin (pin 9 for TDA6650ATT and pin 30 for TDA6651ATT) must not be connected to a voltage higher than 3.6 V.
Fig 5.
Input admittance (s11) of the low band mixer (40 MHz to 200 MHz); Yo =20mS
mce160
0.2
2
1
0.5
10
5
0.2
2
1
0.5
10
5
0
+ j
j
0.2
0.5
1
2
5
10
40 MHz
200 MHz
相关PDF资料
PDF描述
TDA6811 SPECIALTY CONSUMER CIRCUIT, PDIP18
TDA6812-5 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP40
TDA6920 7-CHANNEL, AUDIO/VIDEO SWITCH, PDIP18
TDA6930S AM, AUDIO/VIDEO DEMODULATOR, PDIP30
TDA6930X AM, AUDIO/VIDEO DEMODULATOR, PDSO28
相关代理商/技术参数
参数描述
TDA6650TT 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog)
TDA6650TT/C3 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog)
TDA6650TT/C3/S2 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog)
TDA6651 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog)
TDA6651ATT 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner (digital and analog)