- 您现在的位置：买卖IC网 > PDF目录225295 > TDA8002C (NXP Semiconductors N.V.) IC Card Interface(IC卡接口) PDF资料下载
参数资料
| 型号： | TDA8002C |
| 厂商： | NXP Semiconductors N.V. |
| 英文描述： | IC Card Interface(IC卡接口) |
| 中文描述： | IC卡接口（集成电路卡接口） |
| 文件页数： | 19/28页 |
| 文件大小： | 139K |
| 代理商： | TDA8002C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
1999 Oct 12
26
Philips Semiconductors
Product specication
IC card interface
TDA8002C
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°C. The top-surface temperature of the
packages should preferable be kept below 230
°C.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45
° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°C.
相关PDF资料 |
PDF描述 |
|---|---|
| TDA8003TS | IIC-bus SIM Card Interface(IIC总线SIM卡接口) |
| TDA8005 | Low-Power Smart Card Coupler(低功耗智能卡藕合器) |
| TDA8006 | Multiprotocol IC Card Coupler(多协议的IC卡耦合器) |
| TDS10 | SLIDE DIP SWITCH-10SWITCHES, SP3T, LATCHED,0.025A, 24VDC, THROUGH HOLE-STRAIGHT |
| TDSG3160 | 7 SEG NUMERIC DISPLAY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA8002C/CD | 功能描述:输入/输出控制器接口集成电路 SMRT CRD INTERFCE IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| TDA8002C/CD-T | 功能描述:输入/输出控制器接口集成电路 SMRT CRD INTERFCE IC RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| TDA8002CG | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:IC card interface |
| TDA8002CG/C1 | 制造商:NXP Semiconductors 功能描述:Cut Tape 制造商:NXP Semiconductors 功能描述:IC Card Interface 32-Pin LQFP T/R |
| TDA8002CG/C1,518 | 功能描述:输入/输出控制器接口集成电路 INTERFACE CARD RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。