- 您现在的位置：买卖IC网 > PDF目录225295 > TDA8005 (NXP Semiconductors N.V.) Low-Power Smart Card Coupler(低功耗智能卡藕合器) PDF资料下载
参数资料
| 型号： | TDA8005 |
| 厂商： | NXP Semiconductors N.V. |
| 英文描述： | Low-Power Smart Card Coupler(低功耗智能卡藕合器) |
| 中文描述： | 低功耗智能卡器（低功耗智能卡藕合器） |
| 文件页数： | 9/32页 |
| 文件大小： | 198K |
| 代理商： | TDA8005 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
1996 Sep 25
17
Philips Semiconductors
Product specication
Low-power smart card coupler
TDA8005
I/O buffer modes (see Fig.8)
The following are the I/O buffer modes:
1. I/O buffer disabled by ENIO.
2. I/O buffer in input, 20 k
pull-up resister connected
between I/O and VCC, I/O masked till 200 clock pulses.
3. I/O buffer in input, 20 k
pull-up resister connected
between I/O and VCC, I/O is sampled every 31 clock
pulses.
4. I/O buffer in output, 20 k
pull-up resister connected
between I/O and VCC.
5. I/O buffer in output, I/O is pulled LOW by the N
transistor of the buffer.
6. I/O buffer in output, I/O is strongly HIGH or LOW by the
P or N transistor.
Output ports extension
In the LQFP64 version, 6 auxiliary output ports may be
used for low frequency tasks (for example, keyboard
scanning). These ports are push-pull output types (cf use
in software document).
Activation sequence
When the card is inactive, VCC, CLK, RST and I/O are
LOW, with low impedance with respect to GND. The
step-up converter is stopped. The I/O is configured in the
reception mode with a high impedance path to the ISO
UART, subsequently no spurious pulse from the card
during power-up will be taken into account until I/O is
enabled. When everything is satisfactory (voltage supply,
card present, no hardware problems), the microcontroller
may initiate an activation sequence by setting START
LOW (t0):
The step-up converter is started (t1)
LIS signal is disabled by ENLI, and VCC starts rising from
0 to 5 V with a controlled rise time of 0.1 V/
s typically
(t2)
I/O buffer is enabled (t3)
Clock is sent to the card (t4)
RST buffer is enabled (t5).
In order to allow a precise count of clock pulses during
ATR, a defined time window (t3; t5) is opened where the
clock may be sent to the card by means of RSTIN. Beyond
this window, RSTIN has no more action on clock, and only
monitors the cards RST contact (RST is the inverse of
RSTIN).
The sequencer is clocked by fINT/64 which leads to a time
interval T of 25
s typical. Thus t1 =0to 164T,
t2 =t1 + 123T, t3 =t1 + 4T, t4 =t3 to t5 and t5 =t1 +7T
(see Fig.9).
Deactivation sequence (see Fig.10)
When the session is completed, the microcontroller sets
START HIGH. The circuit then executes an automatic
deactivation sequence:
Card reset (RST falls LOW) at t
10
Clock is stopped at t11
I/O becomes high impedance to the ISO UART (t12)
VCC falls to 0 V with typical 0.1 V/s slew rate (t13)
The step-up converter is stopped and CLK, RST, VCC
and I/O become low impedance to GND (t14).
t10 < 164T; t11 =t10 + 12T; t12 =t10 + T; t13 =t10 + 123T;
t14 =t10 + 5T.
Protections
Main hardware fault conditions are monitored by the circuit
Overcurrent on V
CC
Short circuits between VCC and other contacts
Card take-off during transaction.
When one of these problems is detected, the security logic
block pulls the interrupt line OFF LOW, in order to warn the
microcontroller, and initiates an automatic deactivation of
the contacts. When the deactivation has been completed,
the OFF line returns HIGH, except if the problem was due
to a card extraction in which case it remains LOW till a card
is inserted.
相关PDF资料 |
PDF描述 |
|---|---|
| TDA8006 | Multiprotocol IC Card Coupler(多协议的IC卡耦合器) |
| TDS10 | SLIDE DIP SWITCH-10SWITCHES, SP3T, LATCHED,0.025A, 24VDC, THROUGH HOLE-STRAIGHT |
| TDSG3160 | 7 SEG NUMERIC DISPLAY |
| TDSY5160 | 7 SEG NUMERIC DISPLAY |
| TE-11211 | TOGGLE SWITCH, DPDT, LATCHED, 5A, 28VDC, PANEL MOUNT-THREADED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA8005A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Low-power 3 V/5 V smart card coupler |
| TDA8005AG | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Low-power 3 V/5 V smart card coupler |
| TDA8005AH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Low-power 3 V/5 V smart card coupler |
| TDA8005G | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Low-power smart card coupler |
| TDA8005H | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Low-power smart card coupler |
发布紧急采购，3分钟左右您将得到回复。