- 您现在的位置：买卖IC网 > PDF目录225295 > TDA8006 (NXP Semiconductors N.V.) Multiprotocol IC Card Coupler(多协议的IC卡耦合器) PDF资料下载
参数资料
| 型号： | TDA8006 |
| 厂商： | NXP Semiconductors N.V. |
| 英文描述： | Multiprotocol IC Card Coupler(多协议的IC卡耦合器) |
| 中文描述： | 多协议IC卡器（多协议的集成电路卡耦合器） |
| 文件页数： | 15/40页 |
| 文件大小： | 166K |
| 代理商： | TDA8006 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
2000 Feb 21
22
Philips Semiconductors
Product specication
Multiprotocol IC Card coupler
TDA8006
UART Transmit Register (UTR; address 4; write only;
all bits cleared after reset)
Bits D7 to D0 are the data bits to be transmitted to the
card. Due to the automatic conversion performed by the
UART according to the convention detected during TS, the
controller must write the characters to send to the card in
direct convention. The character to be sent may be written
to the UTR as soon as bit TBE (Transmit Buffer Empty) is
set in the status register.
If writing to the UCR occurs after 12.5 ETU + GT after the
previous start bit, then the transmission starts on the rising
edge of EN during the write operation. If writing to the UCR
occurs before 12.5 ETU + GT after the previous start bit,
the UART waits until 12.5 ETU + GT after the previous
start bit before starting the transmission.
In protocol T = 0, if a parity error is signalled by the card,
the previous character must be rewritten to the UTR.
The UART will then wait 13 ETU after the start bit of the
previous character before restarting the transmission.
STATUS REGISTER AND INTERRUPTS
The ISO 7816 UART reports its activity to the
microcontroller through the UART status register, which
acts upon the interrupt line INT.
All bits except for D5 generate an interrupt on INT, if
enabled, when they are set. D0, D2, D3, D4, D6 and D7
are cleared on the rising edge of EN after a read operation
of the USR. D1 is cleared when the data in the reception
buffer has been read-out. D5 may be used to check the
card’s presence and also to determine the reason for an
emergency deactivation during a card’s session. In case of
Early Answer (EA) or Mute Card (MC) during automatic
ATR processing, the card is not automatically deactivated.
If enabled, an interrupt is generated, and the controller
then decides to deactivate or not.
Table 11 UART Status Register (USR; address 5; read only; all bits cleared after reset except for D5)
BIT
NAME
DESCRIPTION
D0
TX Buffer Empty (TBE)
this bit is set when the UART has nished transmitting the data written in
the UTR (at 10.8 ETU) or on the rising edge of TRN; it is reset on the rising
edge of EN during a read status operation
D1
RX Buffer Full (RBF)
this bit is set when the UART has nished receiving a character from the card
(at 10.5 ETU); it is reset on the falling edge of EN during the read status
operation
D2
First Start Detect (FSD)
this bit is set on the falling edge of the rst start bit if SS = 1; it is reset on the
rising edge of EN during a read status operation
D3
Parity Error (PE)
this bit is set when a parity error has been detected by the UART in
transmission or in reception mode at the same time as TBE and RBF; it is
reset on the rising edge of EN during a read status operation
D4
Early Answer (EA)
this bit is set if a start bit has been detected on I/O between the 200 and 400
rst CLK pulses when the UART is congured in automatic ATR processing; it
is reset on the rising edge of EN during a read status operation
D5
OFF
this bit is set if the card is present and reset if the card is not present;
if CMDVCC is set HIGH, it may also be reset if a hardware problem causing
an emergency deactivation sequence has occurred
D6
Off Interrupt (OFFI)
this bit is set when OFF state has changed; it is reset on the rising edge of EN
during a read status operation
D7
Mute Card (MC)
this bit is set if a card has not answered after 80200 CLK pulses for versions
C2 and C3 (90000 for version C1), when the ISO 7816 UART is congured in
automatic ATR processing; it is reset on the rising edge of EN during a read
status operation
相关PDF资料 |
PDF描述 |
|---|---|
| TDS10 | SLIDE DIP SWITCH-10SWITCHES, SP3T, LATCHED,0.025A, 24VDC, THROUGH HOLE-STRAIGHT |
| TDSG3160 | 7 SEG NUMERIC DISPLAY |
| TDSY5160 | 7 SEG NUMERIC DISPLAY |
| TE-11211 | TOGGLE SWITCH, DPDT, LATCHED, 5A, 28VDC, PANEL MOUNT-THREADED |
| TE5D-12.8MHZ | TCVCXO, CLOCK, 12.8 MHz, HCMOS OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA8006AH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler |
| TDA8006AH/C1 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler |
| TDA8006AH/C2 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler |
| TDA8006AH/C3 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Multiprotocol IC Card coupler |
| TDA8006AH/C325,518 | 功能描述:输入/输出控制器接口集成电路 ONE CHIP SMART CARD INTERFACE RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。