参数资料
型号: TEA1104T-T
厂商: NXP SEMICONDUCTORS
元件分类: 电源管理
英文描述: 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
文件页数: 11/16页
文件大小: 100K
代理商: TEA1104T-T
1996 Feb 26
4
Philips Semiconductors
Objective specication
Cost effective battery monitor and fast
charge IC for NiCd and NiMH chargers
TEA1104; TEA1104T
PINNING
SYMBOL
PIN
DESCRIPTION
GND
1
ground
NTC
2
negative temperature coefficient
resistor input
VS
3
stabilized supply voltage
Vbat
4
battery voltage sensing
Rref
5
reference resistor
VP
6
positive supply voltage
OSC
7
oscillator input
LED
8
LED output
Fig.2 Pin configuration.
handbook, halfpage
1
2
3
4
8
7
6
5
MGE353
TEA1104
LED
OSC
NTC
VP
Rref
Vbat
Vs
GND
INTRODUCTION
The operation of the TEA1104; TEA1104T is explained
with the aid of the application diagram illustrated in Fig.7.
An application note (AN95085) is available describing the
versatility of the TEA1104; TEA1104T.
An external power current source charges the batteries via
an electronic switch which is controlled by the TEA1104.
The TEA1104 monitors the battery voltage. Fully charged
batteries are detected when the battery voltage peaks. In
fact, a voltage drop of 0.25% with respect to the top value
is detected. Fast charging is initiated at ‘power on’ or at
‘replaced batteries’. The switch is continuously on,
providing that all protection levels are met. At battery full
detection, the charge current is duty cycled to reduce the
average charge current to a lower level, keeping the
batteries fully charged but at he same time assuring long
battery life. In Fig.3 the battery voltage during fast charge
is plotted.
FUNCTIONAL DESCRIPTION
A block diagram of the TEA1104; TEA1104T is illustrated
in Fig.1
Mode latch
The Mode latch determines if the system is in the fast or in
the slow charge mode.
Fast charge is active at:
– power switch-on and battery connected
– temperature between minimum and maximum value
– battery insert
Trickle charge is active if:
– battery full is detected
– maximum time is exceeded
– maximum cut-off temperature is exceeded after the
initial phase.
Supply block
For correct start-up, the IC supply current is limited to
35
A (typ.) until the start-up voltage of 6.4 V is reached
(standby mode). Thereafter, the operating supply voltage
VP has to be within the window of 5.45 to 11.5 V, meaning
that there is no need for an external voltage regulator to
supply the IC.
The supply block delivers the following outputs:
With the help of an external resistor (pin Rref), a
reference current is obtained which defines the
accuracy of all IC timing characteristics
Externally available 4.25 V stabilized voltage source
(Vsource). This source is used internally to supply a large
part of the circuit and can be used to set the NTC biasing
and to supply other external circuitry with a maximum
current of 1 mA. Protection information is provided via
VS, to design a dual LED indicator
Power-on reset pulse resets all digital circuitry after a
start or restart, due to an interrupted VS.
相关PDF资料
PDF描述
TEA1401T-T 1 A SWITCHING REGULATOR, 150 kHz SWITCHING FREQ-MAX, PDSO20
TEA1506AP/N1,112 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8
TEA1612T SPECIALTY ANALOG CIRCUIT, PDSO24
TEA1742T 2 A POWER FACTOR CONTROLLER, 150 kHz SWITCHING FREQ-MAX, PDSO8
TEA1761T/N2 1.4 A SWITCHING CONTROLLER, PDSO8
相关代理商/技术参数
参数描述
TEA1110 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Low voltage versatile telephone transmission circuit with dialler interface
TEA1110A 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:LOW VOLTAGE VERSATILE TELEPHONE TRANSMISSION CIRCUIT WITH DIALLER INTERFACE
TEA1110A_10 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:LOW VOLTAGE VERSATILE TELEPHONE TRANSMISSION CIRCUIT WITH DIALLER INTERFACE
TEA1110AG-D14-T 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:LOW VOLTAGE VERSATILE TELEPHONE TRANSMISSION CIRCUIT WITH DIALLER INTERFACE
TEA1110AG-S14-R 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:LOW VOLTAGE VERSATILE TELEPHONE TRANSMISSION CIRCUIT WITH DIALLER INTERFACE