- 您现在的位置：买卖IC网 > PDF目录98227 > THS4275MDGNREPR (TEXAS INSTRUMENTS INC) 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | THS4275MDGNREPR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| 封装： | POWERPAD, PLASTIC, MSOP-8 |
| 文件页数： | 20/36页 |
| 文件大小： | 598K |
| 代理商： | THS4275MDGNREPR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
THS4271EP
THS4275EP
SGLS270A DECEMBER 2004 REVISED APRIL 2005
www.ti.com
27
parallel combination of the shunt resistor and the input
impedance of the destination device: this total
effective impedance should be set to match the trace
impedance. If the 6-dB attenuation of a doubly
terminated transmission line is unacceptable, a long
trace can be series-terminated at the source end only.
Treat the trace as a capacitive load in this case and set
the series resistor value as shown in the plot of R(ISO)
vs capacitive load. This does not preserve signal
integrity or a doubly-terminated line. If the input
impedance of the destination device is low, there is
some signal attenuation due to the voltage divider
formed by the series output into the terminating
impedance.
5.
Socketing a high speed part like the THS4271 is
not recommended. The additional lead length and
pin-to-pin capacitance introduced by the socket can
create a troublesome parasitic network, which can
make it almost impossible to achieve a smooth, stable
frequency response. The best results are obtained by
soldering the THS4271 onto the board.
PowerPAD
DESIGN CONSIDERATIONS
The
THS4271
and
THS4275
are
available
in
a
thermally-enhanced PowerPAD family of packages.
These packages are constructed using a downset
leadframe
upon
which
the
die
is
mounted
[see
Figure 90(a) and Figure 90(b)]. This arrangement results
in the lead frame being exposed as a thermal pad on the
underside of the package [see Figure 90(c)]. Because this
thermal pad has direct thermal contact with the die,
excellent thermal performance can be achieved by
providing a good thermal path away from the thermal pad.
The PowerPAD package allows both assembly and
thermal management in one manufacturing operation.
During the surface-mount solder operation (when the
leads are being soldered), the thermal pad can also be
soldered to a copper area underneath the package.
Through the use of thermal paths within this copper area,
heat can be conducted away from the package into either
a ground plane or other heat dissipating device.
The PowerPAD package represents a breakthrough in
combining the small area and ease of assembly of surface
mount with the heretofore awkward mechanical methods
of heatsinking.
Figure 90. Views of Thermally Enhanced
Package
DIE
Side View (a)
DIE
End View (b)
Thermal
Pad
Bottom View (c)
Although there are many ways to properly heatsink the
PowerPAD package, the following steps illustrate the
recommended approach.
Figure 91. PowerPAD PCB Etch and Via
Pattern
Single or Dual
68 Mils x 70 Mils
(Via diameter = 13mils)
PowerPAD PCB LAYOUT CONSIDERATIONS
1.
Prepare the PCB with a top side etch pattern as shown
in Figure 91. There should be etch for the leads as well
as etch for the thermal pad.
2.
Place five holes in the area of the thermal pad. The
holes should be 13 mils in diameter. Keep the holes
small so that solder wicking through the holes is not a
problem during reflow.
3.
Additional vias may be placed anywhere along the
thermal plane outside of the thermal pad area. They
help dissipate the heat generated by the THS4271
and THS4275 IC. These additional vias may be larger
than the 13-mil diameter vias directly under the
thermal pad. They can be larger because they are not
in the thermal pad area to be soldered, so that wicking
is not a problem.
4.
Connect all holes to the internal ground plane.
5.
When connecting these holes to the ground plane, do
not use the typical web or spoke via connection
methodology. Web connections have a high thermal
resistance connection that is useful for slowing the
heat transfer during soldering operations. This
resistance makes the soldering of vias that have plane
connections easier. In this application, however, low
thermal resistance is desired for the most efficient
heat transfer. Therefore, the holes under the THS4271
and THS4275 PowerPAD package should make their
connection to the internal ground plane, with a
complete connection around the entire circumference
of the plated-through hole.
相关PDF资料 |
PDF描述 |
|---|---|
| THS4271MDREPR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4271MDGNTEPR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4271MDEPR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4275MDEPR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
| THS4275MDREPR | 1 CHANNEL, VIDEO AMPLIFIER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS4281 | 制造商:TI 制造商全称:Texas Instruments 功能描述:VERY LOW-POWER, HIGH-SPEED, RAIL-TO-RAIL INPUT AND OUTPUT VOLTAGE-FEEDBACK OPERATIONAL AMPLIFIER |
| THS4281D | 功能描述:高速运算放大器 Very Lo-Pwr R-To-R I/O Voltage Feedback RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS4281DBVR | 功能描述:高速运算放大器 Very Lo-Pwr R-To-R I/O Voltage Feedback RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS4281DBVRG4 | 功能描述:高速运算放大器 Very Lo-Pwr R-To-R I/O Voltage Feedback RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| THS4281DBVT | 功能描述:高速运算放大器 Very Lo-Pwr R-To-R I/O Voltage Feedback RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。