参数资料
| 型号： | TISP4165H4BJR |
| 厂商： | Bourns Inc. |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | SURGE SUPP 135V BIDIR DO-214AA |
| 标准包装： | 3,000 |
| 电压 - 击穿： | 165V |
| 电压 - 断路： | 135V |
| 电压 - 导通状态： | 3V |
| 电流 - 峰值脉冲(8 x 20µs)： | 300A |
| 电流 - 峰值脉冲(10 x 1000µs)： | 100A |
| 电流 - 保持 (Ih)： | 225mA |
| 元件数： | 1 |
| 电容： | 79pF |
| 封装/外壳： | DO-214AA，SMB |
| 包装： | 带卷 (TR) |
TISP4xxxH4BJ Overvoltage Protector Series
APPLICATIONS INFORMATION
Deployment
These devices are two terminal overvoltage protectors. They may be used either singly to limit the voltage between two conductors (Figure 12)
or in multiples to limit the voltage at several points in a circuit (Figure 13).
Th3
Th1
Th1
Th2
Figure 12. Two Point Protection
Figure 13. Multi-point Protection
In Figure 12, protector Th1 limits the maximum voltage between the two conductors to ± V(BO). This configuration is normally used to protect
circuits without a ground reference, such as modems. In Figure 13, protectors Th2 and Th3 limit the maximum voltage between each conduc-
tor and ground to the ± V(BO) of the individual protector. Protector Th1 limits the maximum voltage between the two conductors to its ± V(BO)
value. If the equipment being protected has all its vulnerable components connected between the conductors and ground, then protector Th1
is not required.
Impulse Testing
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table below shows some common values.
Peak Voltage
Voltage
Peak Current
Current
TISP4xxxH4
Series
Standard
Setting
V
Waveform
μ s
Value
A
Waveform
μ s
25 ° C Rating
A
Resistance
?
GR-1089-CORE
2500 2/10 500 2/10 500
1000 10/1000 100 10/1000 100
0
1500 10/160 200 10/160 250 0
FCC Part 68
(March 1998)
800 10/560 100 10/560 160 0
1500 9/720 ? 37.5 5/320 ? 200 0
1000 9/720 ? 25 5/320 ? 200 0
I3124 1500 0.5/700 37.5 0.2/310 200 0
ITU-T K.20/K.21
1500
4000
10/700
37.5
100
5/310 200 0
? FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K.21 10/700 impulse generator
If the impulse generator current exceeds the protector ’s current rating, then a series resistance can be used to reduce the current to the
protector ’s rated value to prevent possible failure. The required value of series resistance for a given waveform is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator ’s peak voltage by the protector’s rated
current. The impulse generator ’s fictive impedance (generator’s peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance. In some cases, the equipment will require verification over a
temperature range. By using the rated waveform values from Figure 11, the appropriate series resistor value can be calculated for ambient
temperatures in the range of -40 ° C to 85 ° C.
NOVEMBER 1997 - REVISED JANUARY 2007
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
相关PDF资料 |
PDF描述 |
|---|---|
| TISP4145M3BJR | SURGE SUPP 120V BIDIR DO-214AA |
| TISP4145H3BJR | SURGE SUPP 120V BIDIR DO-214AA |
| TISP4125M3BJR | SURGE SUPP 100V BIDIR DO-214AA |
| TISP4115M3BJR | SURGE SUPP 90V BIDIR DO-214AA |
| TISP4080M3BJR | SURGE SUPP 65V BIDIR DO-214AA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TISP4165H4BJRS | 制造商:Bourns Inc 功能描述: |
| TISP4165H4BJR-S | 功能描述:硅对称二端开关元件 RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP4165H4BJ-S | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:HIGH HOLDING CURRENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4165J1 | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4165J1BJR | 功能描述:硅对称二端开关元件 RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
发布紧急采购，3分钟左右您将得到回复。