- 您现在的位置：买卖IC网 > PDF目录98246 > TLE5250 (INFINEON TECHNOLOGIES AG) STEPPER MOTOR CONTROLLER, 3 A, PZFM15 PDF资料下载
参数资料
| 型号： | TLE5250 |
| 厂商： | INFINEON TECHNOLOGIES AG |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 3 A, PZFM15 |
| 封装： | PLASTIC, SIP-15 |
| 文件页数： | 19/22页 |
| 文件大小： | 142K |
| 代理商： | TLE5250 |
TLE 5250
Semiconductor Group
6
1998-02-01
Nominal-Current Input
The peak current in the motor winding is defined by the voltage on the Nominal input.
This is compared by a fast comparator to the voltage drop on the actual-current sensor.
If the nominal current is exceeded, the sink transistors of the outputs are turned off by
the logic.
RC/Sync Input
The outputs are turned on by the signal applied to the RC input. Synchronization is
possible by TTL signal or chopper mode with an external RC combination.
Chopper Mode
After the supply voltage is applied, capacitor CT is charged with constant current of
1 mA. A regulator limits the maximum voltage on the capacitor to 2.3 V. As a result of the
rising current in the motor winding, the voltage on the actual sensor increases. Once the
value defined by the nominal-current input is exceeded, the fast comparator resets an
RS flipflop. Thus sink transistors T3 and T4 are turned off by the logic. The charge
current is turned off and the parallel RT discharges CT.
The internal logic is designed so that capacitor CT is always charged before the
discharge operation is triggered. This guarantees a constant charge time, even for very
small coil currents (see Figure 7).
Sync Operation
If a sync signal with TTL level is applied to the RC input, the negative edge will set the
RS flipflop - by way of the combined Schmitt trigger and monoflop - if the voltage on the
current sensor is smaller than the nominal value on the nominal-current input. As in
chopper mode, the appropriate output transistors conduct. They are again turned off by
resetting the RS flipflop when the voltage on the current sensor becomes greater than
the nominal value (see Figure 8).
Output-Stage Control
This part of the circuit handles turn-off of the output stages when the output is shorted to
ground. There is separate current monitoring for this purpose in the source transistors.
The temperature of the output stages is also monitored. If this exceeds 175
°C, all output
stages are turned off, and then turned on again when the temperature drops.
Undervoltage also causes turn-off of the transistors in the output stages. These possible
fault states are stored in the diagnostics register.
相关PDF资料 |
PDF描述 |
|---|---|
| TLE6208-3G | BRUSH DC MOTOR CONTROLLER, 1.2 A, PDSO14 |
| TLE6208-6G | BRUSH DC MOTOR CONTROLLER, 2 A, PDSO28 |
| TLE6210G | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 |
| TLE6266G | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| TLE6280GP | BRUSHLESS DC MOTOR CONTROLLER, PDSO36 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLE6208-3G | 功能描述:马达/运动/点火控制器和驱动器 Triple-Half-Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TLE6208-3-G | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:Triple-Half-Bridge |
| TLE6208-3G_07 | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:Triple Half Bridges Optimized for DC motor management applications |
| TLE62083GXUMA1 | 制造商:Infineon Technologies AG 功能描述:Triple Half Bridge Motor Driver 14-Pin DSO 制造商:Infineon Technologies AG 功能描述:BODY BRIDGES - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC MOTOR DRIVER SPI 14DSO |
| TLE6208-6 | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:Hex-Half-Bridge / Double Six-Driver |
发布紧急采购，3分钟左右您将得到回复。