参数资料
型号: TLE6266G
厂商: INFINEON TECHNOLOGIES AG
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PDSO28
封装: 18 MM, PLASTIC, SOP-28
文件页数: 13/50页
文件大小: 1020K
代理商: TLE6266G
Datasheet TLE 6266 G
Version 2.21
20
July 29th, 2005
periodically activated by entering the cyclic wake HS ON mode. The autotiming period
is programable via SPI (see Table 2).This has to be done, to minimize the current
consumption depending on the cyclic wake time (see Figure 21).
In the cyclic wake mode, the PWM signal is used to switches HS3 from the cyclic HS ON
to the cyclic HS OFF state, if correctly triggered within the long open window (see Figure
17). This is called the “fail-safe PWM” feature
The SPI output bit 14 monitors a thermal shutdown of the switches, whereas output bit
4 flags a thermal prewarning. So the microcontroller is able to reduce the power
dissipation of the TLE 6266 by switching off functions of minor priority before the
temperature threshold of the thermal shutdown is reached. As soon as the under-voltage
condition of the supply voltage is met (VS < VUVOFF), the switches are automatically
disabled by the under-voltage lockout circuit. This is flagged by the SPI output bit 3.
Moreover the switch is disabled when a reset occurs. After the second correct triggered
watchdog, the switch is released for usage.
6.13
Low Side Switches 1 & 2
The two low side outputs OUTL1 and OUTL2 are able to switch loads up to 100 mA.
Their on-resistance is 1.5
typ. @ 25°C. This switches are controlled via the SPI input
bits 5 and 6. In case of high inrush currents a built in zener circuit (typ. 37 V) activates
the switches to protect them.
The SPI diagnosis bit 14 monitors a thermal shutdown of the switches, whereas bit 4
flags a thermal prewarning. So the microcontroller is able to reduce the power dissipation
of the TLE 6266 by switching off functions of minor priority before the temperature
threshold of the thermal shutdown is reached. The SPI output bits 5/6 are giving a
feedback about current status (ON/OFF) of OUTL1/OUTL2. As soon as the under-
voltage condition of the supply voltage is met (VS < VUVOFF), the switches are
automatically disabled by the under-voltage lockout circuit. This is flagged by the SPI
diagnosis bit 3. In addition the outputs OUTL1 and OUTL2 are disabled when a reset
occurs. After the second correct triggered watchdog, the switches are released for
usage.
6.14
Wake Up Pin
This pin is used to wake up the TLE 6266 with an external signal from the C. The
feature is active during cyclic HS OFF mode to switch the transceiver into the cyclic HS
ON mode before starting up the C. A correct wake up signal is a rising edge at the WK
pin during cyclic HS OFF mode. The WK pin has an implemented pull down resistance.
6.15
Timebase Test
This test is useful to measure the internal cycle time of the TLE 6266. The C may use
this information to activate special functions or routines in the cyclic wake mode, which
相关PDF资料
PDF描述
TLE6280GP BRUSHLESS DC MOTOR CONTROLLER, PDSO36
TLE6361G SWITCHING REGULATOR, 425 kHz SWITCHING FREQ-MAX, PDSO36
TLE6363G DUAL SWITCHING CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDSO14
TLE6365G SWITCHING REGULATOR, 115 kHz SWITCHING FREQ-MAX, PDSO8
TLE6387GV60 1 A SWITCHING CONTROLLER, 430 kHz SWITCHING FREQ-MAX, PDSO14
相关代理商/技术参数
参数描述
TLE6266GNT 制造商:Infineon Technologies AG 功能描述:CAN 125KBd Shutdown 5V Automotive 28-Pin DSO
TLE6270R 功能描述:基准电压& 基准电流 POWERTRAIN RoHS:否 制造商:STMicroelectronics 产品:Voltage References 拓扑结构:Shunt References 参考类型:Programmable 输出电压:1.24 V to 18 V 初始准确度:0.25 % 平均温度系数(典型值):100 PPM / C 串联 VREF - 输入电压(最大值): 串联 VREF - 输入电压(最小值): 分流电流(最大值):60 mA 最大工作温度:+ 125 C 封装 / 箱体:SOT-23-3L 封装:Reel
TLE6270RAUMA1 制造商:Infineon Technologies AG 功能描述:QUAD LOW SIDE INJECTOR DRIVER 制造商:Infineon Technologies AG 功能描述:ENGINECONTROL_IC - Tape and Reel 制造商:Infineon Technologies AG 功能描述:IC DRIVER INJECTOR QUAD DSO-36
TLE6280 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:3-Phase Bridge Driver IC
TLE6280GP 功能描述:马达/运动/点火控制器和驱动器 GATE DRIVER ICS FOR EXTERNAL MOSFETS RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube