参数资料
型号: TLE6368R
厂商: Infineon Technologies
文件页数: 16/59页
文件大小: 0K
描述: IC PS SYSTEM MULTI VOLT PDSO-36
标准包装: 800
应用: 电源,汽车应用
输入电压: 5.5 V ~ 60 V
输出数: 3
输出电压: 2.6V,3.3V,5V
工作温度: -40°C ~ 150°C
安装类型: 表面贴装
封装/外壳: 36-BSSOP(0.433",11.00mm 宽)裸露焊盘
供应商设备封装: PG-DSO-36
包装: 带卷 (TR)
配用: DEMOBOARDTLE6368IN-ND - BOARD DEMO FOR TLE 6368
其它名称: SP000014666
TLE6368RNT
TLE6368RT
TLE 6368 / SONIC
the closed window (CW) starts. Then three valid watchdog triggers are shown, no effect
on the reset line and/or error pin is observed. With the missing watchdog trigger signal
the error signal turns low immediately where the reset is asserted after another delay of
half the closed window time.
Also shown in the figure are two typical failure modes, one pretrigger and one missing
signal. In both cases the error signal will go low immediately the failure is detected with
the reset following after the half closed window time.
2.10
Overtemperature Protection
At a chip temperature of more than 150° an error and temperature flag is set and can be
read through the SPI. The device is switched off if the device reaches the
overtemperature threshold of 170°C. The overtemperature shutdown has a hysteresis to
avoid thermal pumping.
2.11
Power Down Mode
The TLE 6368 G1 / SONIC is started by a static high signal at the wake input or a high
pulse with a minimum of 50μs duration at the Wake input (pin 34). Voltages in the range
between the turn on and turn off thresholds for a few 100μs must be avoided!
By SPI command (“Sleep”-bit, D8, equals zero) all voltage regulators including the
switching regulator except the standby regulator can be turned off completely only if the
wake input is low. In the case the Wake input is permanently connected to battery the
device cannot be turned off by SPI command, it will always turn on again.
For stable “on” operation of the device the “Sleep”-bit, D8 has to be set to high at each
SPI cycle!
When powering the device again after power down the status of the SPI controlled
devices (e.g. trackers, watchdog etc.) depends on the output voltage on Q_LDO1. Did
the voltage at Q_LDO1 decrease below 3.3V the default status (given in the next section)
is set otherwise the last SPI command defines the status.
2.12
Serial Peripheral Interface
A standard 16 bit SPI is available for control and diagnostics. It is capable to operate in
a daisy chain. It can be written or read by a 16 bit SPI interface as well as by an 8 bit SPI
interface.
The 16-bit control word (write bit assignment, see Figure 8) is read in via the data input
DI, synchronous to the clock input CLK supplied by the μC beginning with the LSB D0.
The diagnosis word appears in the same way synchronously at the data output DO (read
bit assignment, see figure 9), so with the first bit shifted on the DI line the first bit appears
on the DO line.
The transmission cycle begins when the TLE 6368 G1 / SONIC is selected by the “not
chip select” input CS (H to L). After the CS input returns from L to H, the word that has
Data Sheet
16
Rev. 2.2, 2006-12-01
相关PDF资料
PDF描述
TLE7368-3E IC PS SYSTEM MULTI VOLT PGDSO-36
TLV1117LV25DCYT IC REG LDO 2.5V 1A SOT223-4
TLV431BH6TA IC VREF SHUNT ADJ SC-70-6
TLV70018QDDCRQ1 IC REG LDO 1.8V .2A SOT23-5
TLV70430DBVT IC REG LDO 3V .15A SOT23-5
相关代理商/技术参数
参数描述
TLE6389 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:Step - Down DC/DC Controller
TLE6389_07 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:Step-Down DC/DC Controller
TLE6389-2G V50 功能描述:DC/DC 开关控制器 Step-Dwn DC/DC CTRLR 5V RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TLE63892GV 功能描述:DC/DC 开关控制器 DC/DC CONVERTER RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TLE6389-2GV 功能描述:DC/DC 开关控制器 Step-Dwn DC/DC CTRLR RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK