参数资料
型号: TLE6368R
厂商: Infineon Technologies
文件页数: 9/59页
文件大小: 0K
描述: IC PS SYSTEM MULTI VOLT PDSO-36
标准包装: 800
应用: 电源,汽车应用
输入电压: 5.5 V ~ 60 V
输出数: 3
输出电压: 2.6V,3.3V,5V
工作温度: -40°C ~ 150°C
安装类型: 表面贴装
封装/外壳: 36-BSSOP(0.433",11.00mm 宽)裸露焊盘
供应商设备封装: PG-DSO-36
包装: 带卷 (TR)
配用: DEMOBOARDTLE6368IN-ND - BOARD DEMO FOR TLE 6368
其它名称: SP000014666
TLE6368RNT
TLE6368RT
TLE 6368 / SONIC
the gate driver supply is managed by the combination of internal charge pump, external
charge pump and bootstrap capacitor.
2.1.1
Current mode control scheme
The regulation loop is located at the left lower corner in the schematic, there you find the
voltage feedback amplifier which gives the actual information of the actual output voltage
level and the current sense amplifier for the load current information to form finally the
regulation signal. To avoid subharmonic oscillations at duty cycles higher than 50% the
slope compensation block is necessary.
The control signal formed out of those three blocks is finally the input of the PWM
regulator for the DMOS gate turn off command, which means this signal determines the
duty cycle. The gate turn on signal is set by the oscillator periodically every 3μs which
leads to a Buck converter switching frequency around 330kHz.
With decreasing input voltage the device changes to the so called pulse skipping mode
which means basically that some of the oscillator gate turn off signals are ignored. When
the input voltage is still reduced the DMOS is turned on statically (100% duty cycle) and
its gate is supplied by the internal charge pump. Below typical 4.5V at the feedback pin
the device is turned off.During normal switching operation the gate driver is supplied by
the bootstrap capacitor.
2.1.2
Start-up procedure
To guarantee a device startup even under full load condition at the linear regulator
outputs a special start up procedure is implemented. At first the bootstrap capacitor is
charged by the internal charge pump. Afterwards the output capacitor is charged where
the driver supply in that case is maintained only by the bootstrap capacitor. Once the
output capacitor of the buck converter is charged the external charge pump is activated
being able to supply the linear regulators and finally the linear regulators are released to
supply the loads.
2.1.3
Reduction of electromagnetic emission
In figure 3 it is recognized that two internal DMOS switches are used, a main switch and
an auxiliary switch. The second implemented switch is used to adjust the current slope
of the switching current. The slope adjustment is done by a controlled charge and
discharge of the gate of this DMOS. By choosing the external resistor on the SLEW pin
appropriate the current transition time can be adjusted between 20ns and 100ns.
2.1.4
Reducing the switching losses
The second purpose of the slope DMOS is to minimise the switching losses. Once being
in freewheeling mode of the buck regulator the output voltage level is sufficient to force
the load current to flow, the input voltage level is not needed in the first moment. By a
feedback network consisting of a resistor and a diode to the boost pin (connection see
Data Sheet
9
Rev. 2.2, 2006-12-01
相关PDF资料
PDF描述
TLE7368-3E IC PS SYSTEM MULTI VOLT PGDSO-36
TLV1117LV25DCYT IC REG LDO 2.5V 1A SOT223-4
TLV431BH6TA IC VREF SHUNT ADJ SC-70-6
TLV70018QDDCRQ1 IC REG LDO 1.8V .2A SOT23-5
TLV70430DBVT IC REG LDO 3V .15A SOT23-5
相关代理商/技术参数
参数描述
TLE6389 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:Step - Down DC/DC Controller
TLE6389_07 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:Step-Down DC/DC Controller
TLE6389-2G V50 功能描述:DC/DC 开关控制器 Step-Dwn DC/DC CTRLR 5V RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TLE63892GV 功能描述:DC/DC 开关控制器 DC/DC CONVERTER RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TLE6389-2GV 功能描述:DC/DC 开关控制器 Step-Dwn DC/DC CTRLR RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK