- 您现在的位置：买卖IC网 > PDF目录385933 > TLV2322Y (Texas Instruments, Inc.) LinCMOSE LOW-VOLTAGE LOW-POWER OPERATIONAL AMPLIFIERS PDF资料下载
参数资料
| 型号： | TLV2322Y |
| 厂商： | Texas Instruments, Inc. |
| 英文描述： | LinCMOSE LOW-VOLTAGE LOW-POWER OPERATIONAL AMPLIFIERS |
| 中文描述： | LinCMOSE低压低功耗运算放大器 |
| 文件页数： | 23/33页 |
| 文件大小： | 502K |
| 代理商： | TLV2322Y |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
TLV2322, TLV2322Y, TLV2324, TLV2324Y
LinCMOS
LOW-VOLTAGE LOW-POWER
OPERATIONAL AMPLIFIERS
SLOS187 – FEBRUARY 1997
23
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
input bias current
Because of the high input impedance of the TLV232x operational amplifier, attempts to measure the input bias
current can result in erroneous readings. The bias current at normal ambient temperature is typically less than
1 pA, a value that is easily exceeded by leakages on the test socket. Two suggestions are offered to avoid
erroneous measurements:
Isolate the device from other potential leakage sources. Use a grounded shield around and between the
device inputs (see Figure 38). Leakages that would otherwise flow to the inputs are shunted away.
Compensate for the leakage of the test socket by actually performing an input bias current test (using a
picoammeter) with no device in the test socket. The actual input bias current can then be calculated by
subtracting the open-socket leakage readings from the readings obtained with a device in the test
socket.
Many automatic testers as well as some bench-top operational amplifier testers use the servo-loop
technique with a resistor in series with the device input to measure the input bias current (the voltage
drop across the series resistor is measured and the bias current is calculated). This method requires
that a device be inserted into a test socket to obtain a correct reading; therefore, an open-socket reading
is not feasible using this method.
V = VIC
8
5
1
4
Figure 38. Isolation Metal Around Device Inputs
(P package)
low-level output voltage
To obtain low-level supply-voltage operation, some compromise is necessary in the input stage. This
compromise results in the device low-level output voltage being dependent on both the common-mode input
voltage level as well as the differential input voltage level. When attempting to correlate low-level output
readings with those quoted in the electrical specifications, these two conditions should be observed. If
conditions other than these are to be used, please refer to the Typical Characteristics section of this data sheet.
input offset voltage temperature coefficient
Erroneous readings often result from attempts to measure the temperature coefficient of input offset voltage.
This parameter is actually a calculation using input offset voltage measurements obtained at two different
temperatures. When one (or both) of the temperatures is below freezing, moisture can collect on both the device
and the test socket. This moisture results in leakage and contact resistance that can cause erroneous input
offset voltage readings. The isolation techniques previously mentioned have no effect on the leakage since the
moisture also covers the isolation metal itself, thereby rendering it useless. These measurements should be
performed at temperatures above freezing to minimize error.
full-power response
Full-power response, the frequency above which the operational amplifier slew rate limits the output voltage
swing, is often specified two ways: full-linear response and full-peak response. The full-linear response is
相关PDF资料 |
PDF描述 |
|---|---|
| TLV2324Y | Inductive DC |
| TLV2341(中文) | LINCMOS<TM> Programmable Low-Voltage OP AMP(电源电流可编程，低电压运放) |
| TLV2342(中文) | Dual LINCMOS<TM> Programmable Low-Voltage OP AMP(LICMOS，低电压，高速双运放) |
| TLV2342Y | LinCMOSE LOW-VOLTAGE HIGH-SPEED OPERATIONAL AMPLIFIERS |
| TLV2344ID | LinCMOSE LOW-VOLTAGE HIGH-SPEED OPERATIONAL AMPLIFIERS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLV2324 | 制造商:TI 制造商全称:Texas Instruments 功能描述:LinCMOSE LOW-VOLTAGE LOW-POWER OPERATIONAL AMPLIFIERS |
| TLV2324ID | 功能描述:运算放大器 - 运放 Quad LiNCMOS RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| TLV2324IDG4 | 功能描述:运算放大器 - 运放 Quad LiNCMOS RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| TLV2324IDR | 功能描述:运算放大器 - 运放 Quad Lo-Vltg Mcrpwr Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| TLV2324IDRG4 | 功能描述:运算放大器 - 运放 Quad Lo-Vltg Mcrpwr Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。