参数资料
型号: TMJ320C6211GNY167
厂商: Texas Instruments, Inc.
元件分类: 数字信号处理
英文描述: FIXED-POINT DIGITAL SIGNAL PROCESSORS
中文描述: 定点数字信号处理器
文件页数: 39/83页
文件大小: 1176K
代理商: TMJ320C6211GNY167
TMS320C6211, TMS320C6211B
FIXED-POINT DIGITAL SIGNAL PROCESSORS
SPRS073K
AUGUST 1998
REVISED MARCH 2004
39
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251
1443
bootmode
The C62x
device resets using the active-low signal RESET signal (for the C6211/C6211B device, the RESET
signal is the same as the internal reset signal). While RESET is low, the internal reset is also asserted and the
device is held in reset and is initialized to the prescribed reset state. Refer to reset timing for reset timing
characteristics and states of device pins during reset. The release of the internal reset signal (see the Reset
Phase 3 discussion in the Reset Timing section of this data sheet) starts the processor running with the
prescribed device configuration and boot mode.
The C6211/C6211B has three types of boot modes:
Host boot
If host boot is selected, upon release of internal reset, the CPU is internally “stalled” while the remainder of
the device is released. During this period, an external host can initialize the CPU’s memory space as
necessary through the host interface, including internal configuration registers, such as those that control
the EMIF or other peripherals. Once the host is finished with all necessary initialization, it must set the
DSPINT bit in the HPIC register to complete the boot process. This transition causes the boot configuration
logic to bring the CPU out of the “stalled” state. The CPU then begins execution from address 0. The DSPINT
condition is not latched by the CPU, because it occurs while the CPU is still internally “stalled”. Also, DSPINT
brings the CPU out of the “stalled” state only if the host boot process is selected. All memory may be written
to and read by the host. This allows for the host to verify what it sends to the DSP if required. After the CPU is
out of the “stalled” state, the CPU needs to clear the DSPINT, otherwise, no more DSPINTs can be received.
Emulation boot
Emulation boot mode is a variation of host boot. In this mode, it is not necessary for a host to load code or to
set DSPINT to release the CPU from the “stalled” state. Instead, the emulator will set DSPINT if it has not
been previously set so that the CPU can begin executing code from address 0. Prior to beginning execution,
the emulator sets a breakpoint at address 0. This prevents the execution of invalid code by halting the CPU
prior to executing the first instruction. Emulation boot is a good tool in the debug phase of development.
EMIF boot (using default ROM timings)
Upon the release of internal reset, the 1K-Byte ROM code located in the beginning of CE1 is copied to
address 0 by the EDMA using the default ROM timings, while the CPU is internally “stalled”. The data should
be stored in the endian format that the system is using. The boot process also lets you choose the width of
the ROM. In this case, the EMIF automatically assembles consecutive 8-bit bytes or 16-bit half-words to
form the 32-bit instruction words to be copied. The transfer is automatically done by the EDMA as a
single-frame block transfer from the ROM to address 0. After completion of the block transfer, the CPU is
released from the “stalled” state and start running from address 0.
相关PDF资料
PDF描述
TMX320C6201GNY167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMX320C6211GNZ167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMP320C6211GNZ167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMX320C6211PYP167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMP320C6211PYP167 FIXED-POINT DIGITAL SIGNAL PROCESSORS
相关代理商/技术参数
参数描述
TMJ320C6211GNZ167 制造商:TI 制造商全称:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMJ320C6211PYP167 制造商:TI 制造商全称:Texas Instruments 功能描述:FIXED-POINT DIGITAL SIGNAL PROCESSORS
TMJ325AB7475KMHP 功能描述:CAP CER 4.7UF 25V X7R 1210 制造商:taiyo yuden 系列:M 包装:剪切带(CT) 零件状态:在售 电容:4.7μF 容差:±10% 电压 - 额定:25V 温度系数:X7R 工作温度:-55°C ~ 125°C 特性:软端子 等级:AEC-Q200 应用:汽车,SMPS 滤波,Boardflex 敏感 故障率:- 安装类型:表面贴装,MLCC 封装/外壳:1210(3225 公制) 大小/尺寸:0.126" 长 x 0.098" 宽(3.20mm x 2.50mm) 高度 - 安装(最大值):- 厚度(最大值):0.110"(2.80mm) 引线间距:- 引线形式:- 标准包装:1
TMJ325AB7475KMHT 功能描述:4.7μF 25V 陶瓷电容器 X7R 1210(3225 公制) 0.126" 长 x 0.098" 宽(3.20mm x 2.50mm) 制造商:taiyo yuden 系列:M 包装:剪切带(CT) 零件状态:有效 电容:4.7μF 容差:±10% 电压 - 额定:25V 温度系数:X7R 安装类型:表面贴装,MLCC 工作温度:-55°C ~ 125°C 应用:汽车级,Boardflex 敏感 等级:AEC-Q200 封装/外壳:1210(3225 公制) 大小/尺寸:0.126" 长 x 0.098" 宽(3.20mm x 2.50mm) 高度 - 安装(最大值):- 厚度(最大值):0.106"(2.70mm) 引线间距:- 特性:软端子 引线形式:- 标准包装:1
TMJ325KB7106KMHP 功能描述:CAP CER 10UF 25V X7R 1210 制造商:taiyo yuden 系列:M 包装:剪切带(CT) 零件状态:在售 电容:10μF 容差:±10% 电压 - 额定:25V 温度系数:X7R 工作温度:-55°C ~ 125°C 特性:软端子 等级:AEC-Q200 应用:汽车,SMPS 滤波,Boardflex 敏感 故障率:- 安装类型:表面贴装,MLCC 封装/外壳:1210(3225 公制) 大小/尺寸:0.126" 长 x 0.098" 宽(3.20mm x 2.50mm) 高度 - 安装(最大值):- 厚度(最大值):0.110"(2.80mm) 引线间距:- 引线形式:- 标准包装:1