参数资料
型号: TMP86FS49BUG
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
封装: 10 X 10 MM, 0.50 MM PITCH, LEAD FREE, PLASTIC, LQFP-64
文件页数: 31/54页
文件大小: 2519K
代理商: TMP86FS49BUG
Page 20
2. Operational Description
2.2 System Clock Controller
TMP86FS49BUG
STOP mode is released by the following sequence.
1. In the dual-clock mode, when returning to NORMAL2, both the high-frequency and low-
frequency clock oscillators are turned on; when returning to SLOW1 mode, only the low-
frequency clock oscillator is turned on. In the single-clock mode, only the high-frequency
clock oscillator is turned on.
2. A warm-up period is inserted to allow oscillation time to stabilize. During warm up, all
internal operations remain halted. Four different warm-up times can be selected with the
SYSCR1<WUT> in accordance with the resonator characteristics.
3. When the warm-up time has elapsed, normal operation resumes with the instruction follow-
ing the STOP mode start instruction.
Note 1: When the STOP mode is released, the start is made after the prescaler and the divider of the
timing generator are cleared to "0".
Note 2: STOP mode can also be released by inputting low level on the RESET pin, which immediately
performs the normal reset operation.
Note 3: When STOP mode is released with a low hold voltage, the following cautions must be observed.
The power supply voltage must be at the operating voltage level before releasing STOP mode.
The RESET pin input must also be “H” level, rising together with the power supply voltage. In this
case, if an external time constant circuit has been connected, the RESET pin input voltage will
increase at a slower pace than the power supply voltage. At this time, there is a danger that a
reset may occur if input voltage level of the RESET pin drops below the non-inverting high-level
input voltage (Hysteresis input).
Note 1: The warm-up time is obtained by dividing the basic clock by the divider. Therefore, the warm-up
time may include a certain amount of error if there is any fluctuation of the oscillation frequency
when STOP mode is released. Thus, the warm-up time must be considered as an approximate
value.
Table 2-2 Warm-up Time Example (at fc = 16.0 MHz, fs = 32.768 kHz)
WUT
Warm-up Time [ms]
Return to NORMAL Mode
Return to SLOW Mode
00
01
10
11
12.288
4.096
3.072
1.024
750
250
5.85
1.95
相关PDF资料
PDF描述
TMP86PS25F 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100
TMP87C800N 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
TMP89FH46LDUG 8-BIT, FLASH, MICROCONTROLLER, PQFP48
TMP89FM42UG 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP44
TMPA8700CPF 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
相关代理商/技术参数
参数描述
TMP86FS49BUG(C,JZ) 功能描述:8位微控制器 -MCU INTEGRATED CIRCUIT MICROCONTROLLER - TLCS870C FAMILY RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
TMP86FS49FG 功能描述:IC MCU FLASH 8BIT 60K 64QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:TLCS-870/C 标准包装:160 系列:HCS12 核心处理器:HCS12 芯体尺寸:16-位 速度:25MHz 连通性:CAN,EBI/EMI,SCI,SPI 外围设备:POR,PWM,WDT 输入/输出数:35 程序存储器容量:128KB(128K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:4K x 8 电压 - 电源 (Vcc/Vdd):2.35 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:52-LQFP 包装:托盘
TMP86FS64FG 制造商:Toshiba America Electronic Components 功能描述:MCU 8BIT TLCS-870 CISC 60KB FLASH 5V 100PQFP - Bulk
TMP86FS64FG(TZ) 功能描述:8位微控制器 -MCU 60K Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
TMP86P202MG 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:8 Bit Microcontroller