
(VSS = 0 V, Topr = 40 to 85°C)
Parameter
Symbol
Pins
Condition
Min
Typ.
Max
Unit
Supply current in NOR-
MAL 1, 2 modes
(Note 7)
IDD
(Note 8)
VDD = 5.5 V
VIN = 5.3 V/0.2 V
VMODE=5.3V/0.1V
fcgck = 10.0 MHz
fs = 32.768 kHz
When a program
operates on flash
memory
14.5
20.0
mA
When a program
operates on RAM
9.5
12.5
Supply current in
IDLE0, 1, 2 modes
5.5
7.5
Supply current in NOR-
MAL 1, 2 modes
(Note 7)
VDD = 5.5 V
VIN = 5.3 V/0.2 V
VMODE=5.3V/0.1V
fcgck = 8.0 MHz
fs = 32.768 kHz
When a program
operates on flash
memory
13
When a program
operates on RAM
8
Supply current in
IDLE0, 1, 2 modes
4.5
Supply current in
SLOW1 mode
(Notes 5 and 7)
VDD = 3.0 V
VIN = 2.8 V/0.2 V
VMODE=2.8V/0.1V
fs = 32.768 kHz
When a program
operates on flash
memory
20
39
μA
When a program
operates on RAM
11
30
Supply current in
SLEEP1 mode
10
24
Supply current in
SLEEP0 mode
9
22
Supply current in STOP
mode
VDD = 5.5 V
VIN = 5.3 V/0.2 V
VMODE=5.3V/0.1V
10
20
Peak current of inter-
mittent operation
(Notes 7 and 9)
IDDRP-P
VDD = 5.5 V
VIN = 5.3 V/0.2 V
VMODE=5.3V/0.1V
When a program
operates on flash
memory or when
data is being read
from flash memory
10
mA
VDD = 3.0V
VIN = 2.8 V/0.2 V
VMODE=2.8V/0.1V
2
Current for writing to
flash memory, erasing
and security program
(Notes 4, 8 and 9)
IDDEW
VDD = 5.5 V
VIN = 5.3 V/0.2 V
VMODE=5.3V/0.1V
26
Note 1: Typical values shown are Topr = 25°C and VDD = 5.0 V, unless otherwise specified.
Note 2: IDD does not include IREF. It is the electrical current in the state in which the peripheral circuitry has been operated.
Note 3: VIN : The input voltage on the pin except MODE pin, VMODE : The input voltage on the MODE pin
Note 4: When performing a write or erase on the flash memory or activating a security program in the flash memory, make sure
that the operating temperature Topr is within the range 10°C to 40°C. If the temperature is outside this range, the resultant
performance cannot be guaranteed.
Note 5: In SLOW1 mode, the difference between the peak current and the average current becomes large.
Note 6: Each supply current in SLOW2 mode is equivalent to that in IDLE0, IDLE1 and IDLE2 modes.
Note 7: When a program operates in the flash memory or when data is being read from the flash memory, the flash memory
operates intermittently, and a peak current flows, as shown in Figure 25-4. In this case, the supply current IDD (in NOR- MAL1, NORMAL2 and SLOW1 modes) is defined as the sum of the average peak current and MCU current.
Note 8: If a write or erase is performed on the flash memory or a security program is enabled in the flash memory, an instantaneous
Note 9: The circuit of a power supply must be designed such as to enable the supply of a peak current. This peak current causes
the supply voltage in the device to fluctuate. Connect a bypass capacitor of about 0.1 μF near the power supply of the
device to stabilize its operation.
TMP89FM42
25. Electrical Characteristics
25.3 DC Characteristics
Page 404
RA004