- 您现在的位置：买卖IC网 > PDF目录19664 > TNY265P (Power Integrations)IC OFFLINE SWIT OTP OCP HV 8DIP PDF资料下载
参数资料
| 型号： | TNY265P |
| 厂商： | Power Integrations |
| 文件页数： | 11/22页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT OTP OCP HV 8DIP |
| 标准包装： | 3,000 |
| 系列： | TinySwitch®-II |
| 输出隔离： | 隔离 |
| 频率范围： | 124kHz ~ 140kHz |
| 输出电压： | 700V |
| 功率（瓦特）： | 11W |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm），7 引线 |
| 供应商设备封装： | DIP-8B |
| 包装： | 管件 |
TNY263-268
core size and design (continuous or discontinuous), ef ?ciency,
minimum speci?ed input voltage, input storage capacitance,
output voltage, output diode forward drop, etc., and can be
different from the values shown in Table 1.
The voltage rating of a resistor should be considered for the
undervoltage detect (Figure 15: R2, R3) resistors. For 1/4 W
resistors, the voltage rating is typically 200 V continuous,
whereas for 1/2 W resistors the rating is typically 400 V
continuous.
Audible Noise
The TinySwitch-II practically eliminates any transformer audio
noise using simple ordinary varnished transformer construction.
No gluing of the cores is needed. The audio noise reduction is
accomplished by the TinySwitch-II controller reducing the
current limit in discrete steps as the load is reduced. This
minimizes the ?ux density in the transformer when switching at
Y-Capacitor
The placement of the Y-capacitor should be directly from the
primary bulk capacitor positive rail to the common/return
terminal on the secondary side. Such placement will maximize
the EMI bene?t of the Y-capacitor and avoid problems in
common-mode surge testing.
audio frequencies.
Optocoupler
Worst Case EMI & Ef ?ciency Measurement
Since identical TinySwitch-II supplies may operate at several
different frequencies under the same load and line conditions,
care must be taken to ensure that measurements are made
under worst case conditions. When measuring ef ?ciency or
EMI verify that the TinySwitch-II is operating at maximum
frequency and that measurements are made at both low and
high line input voltages to ensure the worst case result is
It is important to maintain the minimum circuit path from the
optocoupler transistor to the TinySwitch-II EN/UV and
SOURCE pins to minimize noise coupling.
The EN/UV pin connection to the optocoupler should be kept
to an absolute minimum (less than 12.7 mm or 0.5 in.), and
this connection should be kept away from the DRAIN pin
(minimum of 5.1 mm or 0.2 in.).
obtained.
Output Diode
Layout
Single Point Grounding
Use a single point ground connection at the SOURCE pin for
the BYPASS pin capacitor and the Input Filter Capacitor
(see Figure 17).
Primary Loop Area
The area of the primary loop that connects the input ?lter
capacitor, transformer primary and TinySwitch-II together
should be kept as small as possible.
Primary Clamp Circuit
A clamp is used to limit peak voltage on the DRAIN pin at turn-
off. This can be achieved by using an RCD clamp (as shown
in Figure 14). A Zener and diode clamp (200 V) across the
primary or a single 550 V Zener clamp from DRAIN to
SOURCE can also be used. In all cases care should be taken
to minimize the circuit path from the clamp components to the
transformer and TinySwitch-II.
Thermal Considerations
Copper underneath the TinySwitch-II acts not only as a single
point ground, but also as a heatsink. The hatched areas
shown in Figure 17 should be maximized for good heat sinking
of TinySwitch-II and the same applies to the output diode.
EN/UV pin
If a line undervoltage detect resistor is used then the resistor
should be mounted as close as possible to the EN/UV pin to
For best performance, the area of the loop connecting the
secondary winding, the output diode and the output ?lter
capacitor, should be minimized. See Figure 17 for optimized
layout. In addition, suf ?cient copper area should be provided
at the anode and cathode terminals of the diode for adequate
heatsinking.
Input and Output Filter Capacitors
There are constrictions in the traces connected to the input
and output ?lter capacitors. These constrictions are present
for two reasons. The ?rst is to force all the high frequency
currents to ?ow through the capacitor (if the trace were wide
then it could ?ow around the capacitor). Secondly, the
Constrictions minimize the heat transferred from the TinySwitch-II
to the input ?lter capacitor and from the secondary diode to
the output ?lter capacitor. The common/return (the negative
output terminal in Figure 17) terminal of the output ?lter
capacitor should be connected with a short, low impedance
path to the secondary winding. In addition, the common/
return output connection should be taken directly from the
secondary winding pin and not from the Y-capacitor
connection point.
PC Board Cleaning
Power Integrations does not recommend the use of “no clean”
?ux.
For the most up-to-date information visit the PI website
at: www.powerint.com.
minimize noise pick up.
11
www.powerint.com
Rev. H 02/09
相关PDF资料 |
PDF描述 |
|---|---|
| RW2-0509D/H2/B | CONV DC/DC 2W 4.5-9VIN +/-09VOUT |
| RW2-0505D/H2/B | CONV DC/DC 2W 4.5-9VIN +/-05VOUT |
| TNY265G-TL | IC OFFLINE SWIT OTP OCP HV 8SMD |
| VE-21Z-CW-F2 | CONVERTER MOD DC/DC 2V 40W |
| ATF1500A-10AC | IC CPLD 32 MACROCELL 10NS 44TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TNY265PG | 功能描述:交流/直流开关转换器 7.5 W (85-265 VAC) 11 W (230 VAC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TNY265PN | 功能描述:交流/直流开关转换器 7.5W 85-265 VAC 11W/230 VAC RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TNY265PN-TL | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Enhanced, Energy Efficient, Low Power Off-line Switcher |
| TNY265PTL | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Enhanced, Energy Efficient, Low Power Off-line Switcher |
| TNY266 | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:Generic PCB for DVD Player using TinySwitch-II |
发布紧急采购，3分钟左右您将得到回复。