- 您现在的位置：买卖IC网 > PDF目录98268 > TPA0242PWPG4 (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 PDF资料下载
参数资料
| 型号： | TPA0242PWPG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| 封装： | GREEN, PLASTIC, HTSSOP-24 |
| 文件页数： | 20/35页 |
| 文件大小： | 806K |
| 代理商： | TPA0242PWPG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
www.ti.com
PC-BEEP OPERATION
C
PCB w
1
2p
PCB
(100 kW)
(13)
Shutdown Modes
TPA0242
SLOS287C – NOVEMBER 1999 – REVISED SEPTEMBER 2004
The PC-BEEP input allows a system beep to be sent directly from a computer through the amplifier to the
speakers with few external components. The input is activated automatically. When the PC-BEEP input is active,
both LINEIN and HPIN inputs are deselected, and both the left and right channels are driven in BTL mode with
the signal from PC-BEEP. The gain from the PC-BEEP input to the speakers is fixed at 0.3 V/V and is
independent of the volume setting. When the PC-BEEP input is deselected, the amplifier returns to the previous
operating mode and volume setting. Furthermore, if the amplifier is in shutdown mode, activating PC-BEEP takes
the device out of shutdown, outputs the PC-BEEP signal, then returns the amplifier to shutdown mode.
The preferred input signal is a square wave or pulse train. To be accurately detected, the signal must have a
minimum of 1.5-Vpp amplitude, rise and fall times of less than 0.1 s and a minimum of eight rising edges. When
the signal is no longer detected, the amplifier returns to its previous operating mode and volume setting.
To ac-couple the PC-BEEP input, choose a coupling-capacitor value to satisfy Equation 13.
The PC-BEEP input can also be dc-coupled to avoid using this coupling capacitor. The pin normally rests at
midrail when no signal is present.
The TPA0242 employs a shutdown mode of operation designed to minimize supply current (IDD) during periods
of nonuse to conserve battery power. The SHUTDOWN input terminal should be held high during normal
operation when the amplifier is in use. Pulling SHUTDOWN low mutes the outputs and puts the amplifier in a
low-current state, with IDD = 150 A. SHUTDOWN should never be left unconnected because amplifier operation
would be unpredictable.
Table 6. HP/LINE, SE/BTL, and Shutdown Functions
INPUTS(1)
AMPLIFIER STATE
HP/LINE
SE/BTL
SHUTDOWN
INPUT
OUTPUT
X
Low
X
Mute
Low
High
Line
BTL
Low
High
Line
SE
High
Low
High
HP
BTL
High
HP
SE
(1)
Do not leave inputs unconnected.
27
相关PDF资料 |
PDF描述 |
|---|---|
| TPA0243DGQR | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| TPA0243DGQ | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| TPA0243DGQG4 | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| TPA0243DGQRG4 | 2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| TPA0252PWPR | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA0242PWPR | 功能描述:音频放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA0242PWPRG4 | 功能描述:音频放大器 St 2W Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA0243 | 制造商:TI 制造商全称:Texas Instruments 功能描述:2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE |
| TPA0243DGQ | 功能描述:音频放大器 2W Mono Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA0243DGQG4 | 功能描述:音频放大器 2W Mono Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。