参数资料
型号: TPS2501DRCT
厂商: TEXAS INSTRUMENTS INC
元件分类: 稳压器
英文描述: 6 A SWITCHING REGULATOR, 1075 kHz SWITCHING FREQ-MAX, PDSO10
封装: 3 X 3 MM, 0.90 MM HEIGHT, PLASTIC, SON-10
文件页数: 37/41页
文件大小: 1641K
代理商: TPS2501DRCT
5
SW
PGND
4
IN
3
EN
2
GND
1
10
9
8
7
6
ENUSB
FAULT
USB
AUX
ILIM
Thermal
Pad
DRCPackage
(TopView)
P0051-03
www.ti.com
SLVS886C – OCTOBER 2008 – REVISED AUGUST 2010
PIN DESCRIPTIONS
SIGNAL
TYPE(1)
DESCRIPTION
NAME
NO.
AUX
10
O
Fixed 5.1-V boost converter output. Connect a low-ESR ceramic capacitor from AUX to PGND.
EN
4
I
Enable input for boost converter. Tie to IN to enable.
ENUSB
7
I
Enable input for the USB switch. Tie to IN or AUX to enable.
FAULT
8
O
Active-low USB fault indicator (open-drain)
GND
5
P
Control/logic ground. Must be tied to PGND close to the IC externally.
ILIM
6
I
Program the nominal USB-switch current-limit threshold with a resistor to GND.
IN
3
I
Input supply voltage for boost converter
PGND
2
P
Source connection for the internal low-side boost-converter power switch. Connect to GND with a
low-impedance connection to the input and output capacitors.
SW
1
P
Boost and rectifying switch input. This node is switched between PGND and AUX. Connect the boost
inductor from IN to SW.
USB
9
O
Output of the USB power switch. Connect to the USB port.
Thermal
Must be soldered to achieve appropriate power dissipation. Connect to GND.
pad
(1)
I = input; O = output; P = power
AUX
AUX is the boost converter output and provides power to the USB switch and to any additional load connected to
AUX. Internal feedback regulates AUX to 5.1 V. Connect a 22-mF ceramic capacitor from AUX to PGND to filter
the boost converter output. See the Component Recommendations section for further details. Additional external
load can be connected to AUX as long as the total current drawn by the USB switch and external load does not
overload the boost converter. See the Determining the Maximum Allowable AUX and USB Current section for
details.
EN
EN is a logic-level input that enables the boost converter. Pull EN above 1 V to enable the device and below 0.7
V to disable the device. EN also disables the USB switch, because the USB switch cannot be run when the
boost converter is disabled.
ENUSB
ENUSB is a logic-level input that enables the USB switch. Pull ENUSB above 1 V to enable the USB switch and
below 0.7 V to disable the USB switch. ENUSB only enables the USB switch. The boost converter is
independent of ENUSB and continues to operate even when ENUSB disables the USB switch.
Copyright 2008–2010, Texas Instruments Incorporated
5
Product Folder Link(s): TPS2500 TPS2501
相关PDF资料
PDF描述
TPS650242RHBR 2-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32
TC74LVX4053F TRIPLE 2-CHANNEL, SGL ENDED MULTIPLEXER, PDSO16
TS3L301DGVRE4 8-CHANNEL, DIFFERENTIAL MULTIPLEXER, PDSO48
TS2576CZ550C0 SWITCHING REGULATOR, 58 kHz SWITCHING FREQ-MAX, SFM5
TC151A5825EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
相关代理商/技术参数
参数描述
TPS2501EVM-337 功能描述:电源管理IC开发工具 Eval Mod for TPS2501 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
TPS2505B1RGWR 功能描述:电源开关 IC - USB Integrated Dual USB Pwr Switch RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube
TPS2511DGN 功能描述:热插拔功率分布 Charging Port Cntrlr & Crnt Ltd Pwr Sw RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2511DGNR 功能描述:热插拔功率分布 Charging Port Cntrlr & Crnt Ltd Pwr Sw RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2511EVM-141 功能描述:电源管理IC开发工具 TPS2511 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V